Manual Hudora 14455 (page 5 of 16) (English, German, Dutch, French, Italian, Spanish)

803100

Zoom out

Zoom in

1/16

5/16

• Open the handlebar clamp by lifting the lever. Insert the handlebar grips into

the T piece of the handlebar stem. (Picture 5) Use your thumbs to press

down both locking buttons until the grips can be easily pushed into the T

piece. Turn the handlebar grips until the locking buttons are positioned in

the two openings intended for them and you hear them click into place.

Check that both handlebar grips are fitted correctly by pulling them out-

wards. If the two handlebar grips can no longer be moved, they are properly

engaged. Now close the handlebar clamp by pressing the lever back down

against the handlebar (Picture 6). The contact pressure of the handlebar

clamp can be finely adjusted using the two rotary screws on the underside.

• The handlebars can be locked into place at different heights. To adjust the

height of the handlebars, release the quick release fastener on the handle-

bars by pushing the lever of the quick release fastener away from the han-

dlebar stem until the lever is parallel to the handlebar stem grip. Pull the

handlebar rod out of the handlebar stem until it is at the required height and

the relevant button has snapped into place. (Picture 7)

• The maximum height cannot be exceeded due to the integrated lock. If the

handlebar is not fitting tightly enough at the required height, open the quick

release fastener again and twist the screw opposite to it further into the

thread so that the fastening bracket fits more tightly to the handlebar rod.

Repeat this process until the handlebar rod can be aligned securely.

• Now close the quick release fastener by pushing the lever down to the han-

dlebar stem (Picture 8).

• You should if necessary, fasten the grub screws (Picture 9) firmer, in order

to avoid disturbing tolerances between the folding mechanism and the

handlebar.

• Always check that all parts are fitting tightly before use, particularly the

folding mechanism, the handlebar lock and the wheels.

TO GET THE SCOOTER READY FOR TRANSPORT AGAIN,

PLEASE CARRY OUT THE FOLLOWING ACTIONS

• Release the quick release fastener by pushing the lever of the quick

release fastener away from the handlebar stem. Please press the lock-

ing button so that the handlebar rod can be moved. (Picture 7)

• Push the handlebar rod as far as it will go into the handlebar stem.

• Close the quick release fastener by pushing the lever of the quick release

fastener down to the handlebar stem (Picture 8).

• Open the handlebar clamp by lifting the lever. Use your thumbs to press

both locking buttons in the handlebar grips and pull the handlebar grips

outwards until they are loosened from the T piece.

• Push the handlebar grips down until they are parallel with the handlebar

shaft and the handlebar holders lock in place.

• Pull up the plastic loop on the folding mechanism (black arrow). (Pic-

ture 3)

• Fold up the scooter by moving the handlebar rod towards the back wheel

until you hear the transport lock click into place.

USAGE INSTRUCTIONS

NOTHING‘S EASY AT FIRST …

... most accidents happen to “beginners” within the first ten minutes. Particu-

lar care should be taken during this stage.

USAGE INSTRUCTIONS

The scooter moves when a foot is used to regularly push off, just as with well-

known children’s scooters. Braking is no problem either – simply step on the

friction brake over the back wheel (mudguard).

We recommend folding the scooter by hand after each use or using the stand.

The stands are of direction of movement, located on the left hand side under

the running board. Their use is ensured through simply folding and unfolding.

Aluminium is a good and light material, but should also be handled carefully as

it is not as hard as steel, for example.

PARKING POSITION

In addition to the side stand, the scooter‘s folding mechanism has a parking

position. This parking position is located between the transport position and

the driving position. You use it as described below:

• Pull up the plastic loop on the folding mechanism (black arrow). (Picture 3)

• Push the handlebar forward until it locks into the parking position at an

angle of approx. 45°. (Picture 4) Now release the plastic loop, the handle-

bar is fixed.

MAINTENANCE AND STORAGE

Use only a dry or damp cloth to clean the product; do not use special cleaning

agents! Check the product for damage or traces of wear and tear before and

after each use. Do not make any structural changes. For your own safety,

please use original spare parts only. These can be sourced from HUDORA. If

parts become damaged or if sharp edges or corners should develop, the prod-

uct may not be used any more. If in any doubt, please contact our service team

(http://www.hudora.de/). Store the product in a safe place where it is protect-

ed from the elements, cannot be damaged, and cannot injure anyone.

Replace damaged or worn assembly parts in order to ensure the safety of your

scooter.

WHEEL CHANGE

Wheels should be replaced when they get worn down. To change the wheels,

loosen the axle fitting with two Allen keys and remove the wheels from the

axle. A screwdriver or Allen key can be used to push the bearings out of the

wheel in order to use them again in the new wheels. However, it is usually ad-

visable to change the bearings when the wheels are being changed. Put the

bearings into the new wheel with the spacer sleeve and mount them to the

frame with the axle screws. Make sure that the axle has been screwed on

tightly before starting again!

BEARINGS

Your kick scooter is equipped with precision ball bearings, which were filled

with grease under high pressure, during manufacture. For this reason, the

rollers of the kick scooter only run lightly and swiftly, while under load. Bear-

ings as well as wear parts are maintenance-free. Caution! Worn bearings make

conspicuous audible noises and their function is constrained. In order to

maintain optimal riding pleasure and to ensure lasting safety, you should re-

place bearings, as soon as they begin to exhibit signs of being worn. In the

case of full load, and daily use, we recommend the replacement of the rollers

and bearings, twice a year.

DISPOSAL ADVICE

Please dispose of the product at the end of its service life in the available dis-

posal return or collection system. For any questions contact your local dump-

ing enterprise.

SERVICE

We make every effort to deliver faultless products. If faults do arise however,

we put just as much effort into rectifying them. You can find numerous infor-

mation on the product, replacement parts, solutions to problems and lost as-

sembly manuals at http://www.hudora.de/.

All images are examples of the design.

EN INSTRUCTIONS ON ASSEMBLY AND USE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hudora 14455 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2.74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hudora 14455 Manual

Product: