212467
19
Zoom out
Zoom in
Previous page
1/30
Next page
6 Reconnect the USB cable that connects the computer and the scanner.
Make sure that the USB cable is properly connected to the back of the
scanner. The USB symbol on the end of the cable (the connector) should
be facing up. When connected correctly, the USB connector feels slightly
loose. When connected incorrectly, the USB plug feels overly tight.
Try connecting the USB cable to a different USB port on your computer.
If the scanner still fails to initialize, run the Repair utility (Windows computers only)
as described in the Scanner has stopped working properly section.
Test scanner hardware
If you think the scanner has a hardware issue, verify that the cables are firmly
connected to the scanner, the computer, and the power source. If the cables are
correctly connected, test the scanner using this procedure.
1 Ensure that the TMA cable on the scanner lid is connected to the back of the
scanner.
2 Ensure that the scanner is not connected to the computer.
3 Reset the scanner. See Reset the scanner.
4 Disconnect the USB cable and power cable from the scanner.
5 Ensure that the scanner power cable is still connected to the power source.
6 Press and hold the Scan(
) and Copy buttons ( ) on the scanner at the
same time while reconnecting the power cable to the scanner.
The TMA should turn on for three seconds and then turn off. After the TMA
turns off, the carriage in the scanner should move forward and backward, and
the scanner lamp should turn on. The scanner lamp should flash six times
while the carriage is still in motion.
7 To end the test, disconnect the power cable.
Scanner has stopped working properly
If the scanner stops scanning, complete the following steps in order. After each
step, start a scan to see if the scanner is working. If not, proceed with the next
step.
A cable might be loose. Ensure that both the USB cable and power cable are
securely connected
Unplug the power cable from the power source, wait 60 seconds, and then
plug it back in.
Restart your computer.
A software conflict might exist on your computer. You might need to reinstall
the HP Image Zone software. To do this, run the Repair utility (Windows
computers only).
Click Start, point to Settings, and then click Control Panel (in Windows
XP, click Start, and click Control Panel).
Click Add/Remove Programs, and then select the HP Image Zone
software.
Troubleshooting
User's Manual 15
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP scanjet 3770 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP scanjet 3770 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info