436321

HP designjet 8000s cutter blade kit Manual

207
Zoom out
Zoom in
Previous page
1/230
Next page
Medium Media type Front Print Rear Print mode
Matte vinyl
chloride
Matte 45°C 40°C 45°C 8 pass bi-
directional
Banner Banner 45°C 40°C 45°C 8 pass bi-
directional
We recommend that the front heater, the print heater and the rear heater be set to lower than 50 °C, 45 °
C and 50 °C, respectively.
NOTE When the print heater temperature is set to high, fixing of the ink on the media is
improved, but media wrinkle or mat print may be caused. Adjust heater temperature according
to the media type and environmental temperature.
When the print heater temperature is set to high, the printer may print at low speed to ensure
stable print quality.
Set the front/rear heater temperature 5 °C higher than the print heater temperature. Bad
temperature balance between the front/rear heater and print heater may cause the media to
wrinkle.
Flow of heater temperature setting
1. If you select the media type when loading the media, the temperature value applies as follows:
●
If the initial temperature value has been set, the heater turns on but heating does not start.
●
If the initial temperature value is set to **, the heater turns off.
2. If the printing job data are sent from the host (PC), either of the following operations is performed
before the print starts:
a. If the HEATER PREF set for the media is SOFTWARE:
●
The temperature set in the RIP (print data, job) overwrites the temperature set in the printer,
and the heating starts. Heating does not start if the temperature value is set to OFF.
●
If the temperature is not set in the RIP (print data, job), heating starts with the temperature
set in the printer.
b. If the HEATER PREF set for the media is HEAT PANEL:
●
The temperature set in the RIP is ignored and heating starts with the temperature set in the
printer.
3. Printing starts when the current temperatures of the front, print, and rear heaters all reach the value
exceeding set temperature -2 °C.
If the current temperature is higher than the set temperature, printing starts without waiting for the
temperature to drop. Even after printing has started, the temperature control makes sure that the
heaters maintain the set temperature.
4. During printing, the temperature can be adjusted by using the HEATER key, and then selecting the
rear, front or print heater, and using the
or keys to change the temperature.
ENWW Heater temperature settings 197
Tell me about… (heater topics)
… 207 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP designjet 8000s cutter blade kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP designjet 8000s cutter blade kit in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info