724190
7
Zoom out
Zoom in
Previous page
1/11
Next page
Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide 7
Configuring the 300 Series Access Points
Access Point Provisioning/Reprovisioning
Provisioning parameters are unique to each access point. These local access point parameters are initially configured on the
controller which are then pushed out to the access point and stored on the access point itself. Aruba recommends that
provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.
Access Point Configuration
Configuration parameters are network or controller specific and are configured and stored on the controller. Network
configuration settings are pushed out to the access point but remain stored on the controller.
Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to the ArubaOS User Guide for
complete details.
Electrical and Environmental Specifications
For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/
safety_addendum.
Electrical
Ethernet:
One 100/1000 Base-T auto-sensing Ethernet RJ45 interface
Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (nominal).
Power:
Maximum (worst-case) power consumption: 13.5W (802.3af PoE) or 12W (DC)
Excludes power consumed by external USB device (and internal overhead); this could add up
to 6W (PoE) or 5.5W (DC) for 5W/1A USB device
Direct DC source: 12Vdc nominal, +/- 5%
Power over Ethernet (PoE): 802.3at and 802.3af complaint source
Connect only to IEC 60950-1 or IEC 60601-1 3rd edition products and power sources.
Environmental
Operating:
Temperature: 0°C to +50°C (+32°F to +122°F)
Humidity: 5% to 93% non-condensing
Storage and transport:
Temperature: -40°C to +70°C (-40°F to +158°F)
Regulatory Information
The following regulatory model names apply to the 300 Series access points:
The instructions for this section are applicable to the AP-304 and AP-305 only.
All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is
responsible for ensuring that grounding is available and meets applicable national and electrical codes.
Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer
que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.
If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an
output rated 12Vdc, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in
the US and Canada.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP Aruba IAP-304 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP Aruba IAP-304 in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info