724190
5
Zoom out
Zoom in
Previous page
1/11
Next page
Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide 5
DHCP Server with vendor-specific options
Verifying Pre-Installation Connectivity
Before installing access points in a network environment, make sure that they are able to locate and connect to the controller
after power on.
Specifically, you must verify the following conditions:
When connected to the network, each access point is assigned a valid IP address
Access points are able to locate the controller
Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.
Identifying Specific Installation Locations
You can mount the 300 Series access point on the ceiling or a wall. Use the access point placement map generated by Aruba’s
RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to
the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF
absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning
phase and adjusted for in RF plan.
Identifying Known RF Absorbers, Reflectors and Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical.
Make sure that these sources are taken into consideration when you attach an access point to its fixed location. Examples of
sources that degrade RF performance include:
Cement and brick
Objects that contain water
Metal
Microwave ovens
Wireless phones and headsets
Installing the Access Point
The 300 Series access points ship with a ceiling rail adapter to attach to a 9/16” or 15/16” ceiling rail. Additional ceiling or wall
mount kits are sold separately as accessories.
1. Pull the necessary cables through a prepared hole in the ceiling tile near where the access point will be placed.
2. Place the adapter against the back of the access point with the adapter at an angle of approximately 30 degrees to the tabs
(see Figure 4).
3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 4).
Aruba Networks, Inc., in compliance with governmental requirements, has designed the 300 Series access points so that only
authorized network administrators can change the settings. For more information about access point configuration, refer to
the ArubaOS Quick Start Guide /Aruba Instant Quick Start Guide and ArubaOS User Guide/Aruba Instant User Guide.
The instructions for this section are applicable to the AP-304 and AP-305 only.
Service to all Aruba Networks products should be performed by an AMCP certified technician or similar.
The installer is responsible for securing the access point onto the ceiling tile rail in accordance with the steps below. Failure
to properly install this product may result in physical injury and/or damage to property.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP Aruba IAP-304 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP Aruba IAP-304 in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info