661752
5
Zoom out
Zoom in
Previous page
1/48
Next page
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety
Before installation, and whenever you are
handling the pump, always disconnect from
the electrical supply.
To prevent injury, never put your fingers into the
mouth of the pump.
Use the handle provided to carry or lift the
pump
When used with a Water Butt for the first
time, ensure the water butt is emptied and
cleaned of all sediment, leaves and
accumulated debris.
Pump assembly :
Attach the metal baseplate to the pump with
the bolts and washers supplied
Screw one of the yellow accessory adaptors
to the inlet of the pump
Ensure seals are fitted to the front between
the pump and the adaptor
Ensure hand tight
Screw the filter onto the adaptor.
The arrow on the filter should point
towards the pump.
Ensure seal is fitted to the front between
the adaptor and the filter
Ensure hand tight
Remove filter adaptor from hose and attach
the suction hose to the filter
Ensure seal is fitted to the front between
the filter and the hose
Ensure all fittings are hand tight
Ensure that the inlet to the suction hose is at
least 150mm (6") under the surface of the
water. If required weight the end of the hose
using a brick.
It is critical that all the seals are present
and that all the joints are airtight.
There should be no elbows or kinks in the
suction hose as this will affect performance.
The installation should be consistant with
the limitations as shown in diagrams A & B
on the cover of this booklet.
Fill the pump chamber to the brim with tap
water using a watering can.
The Hozelock garden pumps are self
priming, therefore they can be primed
without filling the suction pipe or filter.
Attach the outlet connector to the outlet of
the pump.
Connect the garden hose to the outlet,
ensuring that the other end of the garden
hose is open and that it will be free to drain
when the pump is turned on.
Ensure that the suction hose is under the
surface of a suitable water reservoir (water
butt etc.).
Plug the pump into a suitable power supply.
When the power is turned on, the pump will
start the priming process. This operation can
take several minutes. During the priming
process the pump is pumping a mixture of air
and water, this drastically reduces the
performance of the pump and is very noisy.
The hose should be open ie. the other end
is not blocked or closed with either a spray
gun or waterstop connector
When the pump is primed and ready to use,
the noise reduces and the flow and pressure
are maximised.
If any of the seals or fittings are missing,
overtightened or loose the pump will not
prime.
If the pump does not prime after 5 minutes
- stop and repeat steps 6 to 10.
TO CONNECT TO AN IRRIGATION SYSTEM:
For use with hoses and hose reels
add a 2166 hose connector
(available separately) .
The Hozelock Garden Pump has a built in
thermal protection switch. The pump stops if
an overload condition occurs. The motor
restarts automatically after it has cooled
down.
Insert the plug into a 220-240v A/C socket.
H
G
F
E
D
C
B
A
Installation
I
J
Overload protection
To start the pump
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hozelock 7816 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hozelock 7816 in the language / languages: All languages as an attachment in your email.

The manual is 5,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info