Manual Hotpoint MF IDC (page 5 of 8) (English)

665377

Zoom out

Zoom in

1/8

Heating or frothing the milk – Automatic

operation

1. Place the container on the base.

2. Remove the milk container’s lid.

3. Fit the appropriate whisk into the holder on the

bottom of the container.

4. Pour the desired amount of milk into the contai-

ner.

5. Fit the lid back onto the container.

6. Use the temperature knob to set the desired

temperature.

7. Insert the power plug into a suitable wall power

outlet. The main led will light up.

8. Press the ON button. The appliance will beep,

the led will start ashing and the frother cycle will

start.

9. When the milk reaches the set temperature, the

cycle automatically stops. If you set cold froth

mode with the knob, the cycle will stop auto-

matically after 60 seconds.

10. The appliance will beep three times when the

cycle terminates.

11. You can interrupt the cycle at any time by pres-

sing the start/stop button. The set temperature

will not be reached if you do so.

12. Once the cycle has terminated, remove the con-

tainer from the base and pour its contents into

a cup or mug. You can use a spoon to push the

froth out of the container, or simply shake the

container slightly while pouring.

13. You can now disconnect the plug from the wall

outlet.

Heating – Keep warm function

This function allows you to froth or heat the milk and

keep it hot at the set temperature. Follow steps 1 to 7

in the previous paragraph.

8. Hold down the start button for more than 2 se-

conds. The appliance will emit a long beep, the

led will start ashing and the frother will start

operating.

9. When the milk reaches its set temperature, the

appliance will stay on for a while before switching

off:

• 20 minutes for the 40°C cycle

• 10 minutes for the 65° and 85° cycles

10. You can interrupt the cycle at any time by pres-

sing the start/stop button.

11. Once the cycle has terminated, remove the con-

tainer from the base and pour its contents into

a cup or mug. You can use a spoon to push the

froth out of the container, or simply shake the

container slightly while pouring.

12. You can now disconnect the plug from the wall

outlet.

This feature is not suitable to keep warm the

milk froth and other drinks like hot chocolate.

FOR BEST RESULTS...

To get the best results, take the milk out of the refrige-

rator immediately before pouring it into the container.

• If you want a rich milky froth, rst run the cold

froth cycle and then a hot froth cycle.

• We recommended using full fat milk for all fro-

thed milk beverages, as it gives a richer froth.

FURTHER INFORMATION

• If the appliance has been left connected to the

power outlet for a long time after use, you must

press the start button twice to turn it on and then

start a cycle.

• Allow the appliance to cool down after using a

hot cycle; do not use it immediately for a second

cycle. Wait a few minutes between cycles.

• After a cold froth cycle, you can immediately

start a new heating or frothing cycle.

MAINTENANCE AND CLEANING

• Always pull the power plug out of the wall outlet

and wait for its motor to stop completely before

cleaning the appliance.

• To avoid the risk of electric shock, do not clean

the base or power cord with water, and never im-

merse them in water.

• The container, whisks and lid can be cleaned

with hot water and a mild detergent, or in the di-

shwasher.

• Take care to dry all parts thoroughly before using

them again.

• The heating base can be cleaned with a soft

damp cloth which has been dipped in a small

amount of detergent. Never immerse it in water

or clean it in a dishwasher.

• Do not use abrasive or aggressive detergents.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint MF IDC in the language / languages: English as an attachment in your email.

The manual is 2,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint MF IDC Manual

Product: