670821

Hotpoint HIP4022 WGT - Ultima Manual

2
Zoom out
Zoom in
Previous page
1/12
Next page
2
FIRST TIME USE
SETTING MENU AND SALT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining
elastic elements from the upper rack.
SETTING MENU
1. Switch on the appliance by pressing the ON/OFF button.
2. Switch off the appliance by pressing the ON/OFF button.
3. Hold down START button for 5 seconds, until you hear a beep.
4. The display shows the first available setting (letter "A"), followed by
its value (for example: 3).
5. Press PREVIOUS/NEXT to scroll the list of the available settings
and to see their value (see the below table), then press START if
you want to change the value of the displayed setting: its value will
start blinking.
6. Use PREVIOUS/NEXT buttons to change the blinking value of the
selected settings, then press START to save the new value: it will
stop blinking.
7. To change another settings repeat steps 5-6.
8. To exit settings menu - press ON/OFF button.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see
PRODUCT DESCRIPTION) and should be filled when the SALT REFILL
indicator light in the control panel is lit.
1.Remove the lower rack and unscrew
the reservoir cap (anticlockwise).
2.Only the first time you do this: fill the
salt reservoir with water.
3.Position the funnel
(see figure)
and fill
the salt reservoir right up to its edge
(approximately 1 kg); it is not unusual
for a little water to leak out.
4.Remove the funnel and wipe any salt
residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
As soon as this procedure is complete, run a program without loading.
The “Soak” program alone is NOT sufficient.
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
After the salt has been poured into the machine, the SALT REFILL
indicator light switches off.
Only use salt that has been specifically designed for dishwashers.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result.
Whenever you need to add salt, we recommend carrying out the
procedure just before the washing cycle is started.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is “3” for average water hardness.
To change, follow instructions in section “SETTING MENU”.
LETTER SETTING
VALUES
(Default - in bold)
Water Hardness Level
(see “Setting the Water Hardness”
and “Water Hardness Table”)
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “Adjusting the dosage of Rinse Aid”)
1 | 2 | 3 | 4 | 5
Start Program
To set the cycle to show at switch on of the
appliance.
“E”= Eco, “L”= Last cycle run
E | L
Brightness Level
To adjust the brightness
level of the display.
“Lo”=Low, “Hi”= High
Lo | Hi
Sound Level
To adjust the volume of the sounds.
“OF” = sounds off, “Lo” = low volume,
“Hi” = high volume.
OF | Lo | Hi
Internal Lights
(see “Options and Functions”)
“On” = On, “OF” = Off
On | OF
Light on the Front
(see “Options and Functions”)
“On” = On, “OF” = Off
On | OF
Factory Settings
To restore to the factory default all the
values of the settings included in the
settings menu. After the activation of this
setting (ON), the machine switches OFF and
restores the factory settings.
“On” = On, “OF” = Off
On | OF
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 17 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint HIP4022 WGT - Ultima at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint HIP4022 WGT - Ultima in the language / languages: English as an attachment in your email.

The manual is 7,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info