670821

Hotpoint HIP4022 WGT - Ultima Manual

10
Zoom out
Zoom in
Previous page
1/12
Next page
10
TROUBLESHOOTING
Your dishwasher may not work properly.
Before contacting the Service Centre check if the problem can be solved by going through the following list.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher won’t
start or does not
respond to com-
mands.
The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. Vigorously push the door until you hear the “click”.
It does not respond to commands. Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and reset the program.
The door doesn’t lock. Racks are not fit to the end. Verify that racks are fit to the end.
The door is not lock. Vigorously push the door until you hear the “clack” sound.
The dishwasher
makes excessive
noise.
The dishes are rattling against each. Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has been pro-
duced.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER). Reset the current cycle by
switching OFF the dishwasher, then switch it on again, select a new program,
press START and close the door. Please do not add any detergent.
The dishes have not
been dried.
The selected program hasn’t any drying
phase.
Verify on the programs table if the selected program has the drying phase.
The rinse aid has run out or the resolution is
not adequate.
Add the rinse aid or adjust the dosage levels higher (see FILLING THE RINSE AID
DISPENSER).
The dishes are made of non-stick or plastic. It is normal the presence of drops of water (see TIPS).
The dishes are not
clean.
The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being
hindered by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle and/or detergent
efficiency is low.
Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been pro-
duced.(see AFTER-SALES SERVICE)
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER). Reset the current cycle by
switching OFF the dishwasher, then switch it on again, select a new program,
press START and close the door. Please do not add any detergent.
The cap on the rinse aid compartment has
not been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged. Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does
not fill the water,
shows "H2O" Warning
or "F06"
No water in the water supply or the tap is
closed.
Make sure there is water in the water supply or the tap running.
The inlet hose is bent. Make sure the drain hose is not bent (see INSTALLATION) reprogram the dish-
washer and reboot.
The sieve in the water inlet hose is clogged; it
is necessary to clean it
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
The dishes and
glasses show calcina-
tion or a whitish film.
The salt level is too low. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The adjustment of the water hardness is not
adequate.
Increase the values (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly
closed.
Check to have properly closed the salt reservoir cap.
The rinse aid is used up or the dosage is insuf-
ficient.
Add the rinse aid or adjust the dosage levels higher.
The dishes and
glasses are blue
streaked or have a
bluish tinge.
The rinse aid dosage is excessive. Adjust the dosage rates below.
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint HIP4022 WGT - Ultima at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint HIP4022 WGT - Ultima in the language / languages: English as an attachment in your email.

The manual is 7,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info