Manual Hotpoint-Ariston WDD 756 (page 10 of 16) (English)

665330

Zoom out

Zoom in

1/16

How to run a wash cycle or a drying

cycle

1. SWITCH THE MACHINE ON. Press the button; the text

HELLO will appear on the display and the START/PAUSE

indicator light will flash slowly in a green colour.

2. LOAD THE LAUNDRY. Open the porthole door. Load the

laundry, making sure you do not exceed the maximum

load value indicated in the table of programmes on the

following page.

3. MEASURE OUT THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Press one of the WASH

CYCLE SELECTOR buttons to select the required wash

cycle; the name of the wash cycle will appear on the

display. A temperature and spin speed is set for each

wash cycle; these may be adjusted. The duration of the

cycle will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin

speed. The machine automatically selects the maximum

temperature and spin speed set for the selected wash

cycle; these values cannot therefore be increased. The

temperature can be decreased by pressing the button,

until the cold wash “OFF” setting is reached. The spin

speed may be progressively reduced by pressing the

button, until it is completely excluded (the “OFF” setting).

If these buttons are pressed again, the maximum values

are restored.

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. When this option

is enabled, the symbol lights up on the display. To

remove the delayed start function press the button

until the text “OFF” appears on the display.

Setting the drying cycle.

The desired drying cycle type may be set by pressing the

DRYING button once or several times. Two options are

available:

A - Based on the how damp the clothes are once they

have been dried:

Iron dry: slightly damp clothes, easy to iron.

Hanger dry: dry clothes to put away.

Cupboard dry: very dry clothes, recommended for

towelling and bathrobes.

B - Based on time: from 40 minutes to 180.

To exclude the drying phase press the relevant button

until the text OFF appears on the display.

If your laundry load to be washed and dried is much

greater than the maximum stated load (see Table of

wash cycles), perform the wash cycle, and when the cycle

is complete, divide the garments into groups and put

some of them back in the drum. At this point, follow the

instructions provided for a “Drying only” cycle. Repeat

this procedure for the remainder of the load.

N.B: a cooling-down period is always added to the end of

each drying cycle.

Drying only

Select a drying setting ( ) using the WASH CYCLE

selector in accordance with the type of fabric, then

select the desired drying type using the DRYING button.

Modifying the cycle settings.

• Press the button to enable the function; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the function; the

indicator light will switch off.

! If the selected function is not compatible with the

programmed wash cycle, the indicator light will flash and

the function will not be activated.

! If the selected function is not compatible with another

function which has been selected previously, the indicator

light corresponding to the first function selected will flash

and only the second function will be activated; the indicator

light corresponding to the enabled function will remain lit.

! The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light will become

green, remaining lit in a fixed manner, and the door will be

locked (the DOOR LOCKED symbol will be on). During

the wash cycle, the name of the phase in progress will

appear on the display. To change a wash cycle while it is

in progress, pause the washer dryer using the START/

PAUSE button (the START/PAUSE indicator light will

flash slowly in an orange colour); then select the desired

cycle and press the START/PAUSE button again.

To open the door while a cycle is in progress, press the

START/PAUSE button; if the DOOR LOCKED symbol is

switched off the door may be opened. Press the START/

PAUSE button again to restart the wash cycle from the

point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be indicated

by the text “END OF CYCLE” on the display; when the

DOOR LOCKED symbol switches off the door may be

opened. Open the door, unload the laundry and switch off

the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped and

the machine will switch off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston WDD 756 in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston WDD 756 Manual

Product: