570818
28
Zoom out
Zoom in
Previous page
1/84
Next page
EN
28
Troubleshooting
Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.
* Only available in selected models.
Problem: Possible causes / Solutions:
The dishwasher does not start or cannot be
controlled.
Switch off the appliance by pressing the ON/OFF button, switch it back
on after approximately one minute and reset the cycle.
The appliance has not been plugged in properly.
The dishwasher door has not been shut properly.
The door won’t close.
The lock was released. Strongly push the door until a “clacking” noise is
heard.
No water drains from the
dishwasher.
The dishwasher cycle has not yet finished.
The water drain hose is bent (see Installation.)
The drain duct is blocked.
The filter is clogged up with food residues.
The dishwasher makes excessive
noise.
The dishes are rattling against each other or against the sprayer arms.
An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use.)
The dishes and glasses are covered
in a white film or limescale deposits.
The level of refined salt is low or the dosage setting is not suitable for
the hardness of the water (see Rinse aid and salt.)
The lid on the salt dispenser is not closed properly.
The rinse aid has been used up or the dosage is too low.
The dishes and glasses are streaked
or have a bluish tinge.
The rinse aid dosage is too high.
The crockery has not been dried
properly.
A wash cycle without a drying cycle has been selected.
The rinse aid has been used up or the dosage is too low (see Rinse aid
and salt.)
The rinse aid setting is not suitable.
The crockery is made from non-stick material or plastic.
The crockery is not clean. The racks are overloaded (see Loading the racks.)
The crockery has not been arranged well.
The sprayer arms cannot rotate freely.
The wash cycle is too gentle (see Wash cycles.)
An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use.)
The lid on the rinse aid compartment has not been shut correctly.
The filter is dirty or blocked (see Care and maintenance.)
The refined salt level is low (see Rinse aid and salt.)
The dishwasher does not take any
water in - Tap shut-off alarm (short
beeps are heard)
*
(the ON/OFF indicator light flashes,
the “Tap shut-off” symbol is lit
and the display shows the text:
No water. Turn tap on. After a few
seconds F 06 appears.)
There is no water in the mains supply.
The water inlet hose is bent (see Installation.)
Turn on the tap and the appliance will start after a few minutes.
The appliance lock has been activated because no action was taken
when the beeps sounded.
Switch off the machine using the ON/OFF button, turn on the tap and
switch the machine back on after a few seconds by pressing the same
button. Re-program the appliance and restart the wash cycle.
Water inlet hose alarm / Water inlet
filter blocked
(the ON/OFF indicator light ashes, the
“Filter” symbol is lit and the display shows
the textF 07.)
Switch off the appliance by pressing the ON/OFF button. Shut off the
water tap to eliminate the risk of flooding and remove the plug from the
electrical socket.
Make sure the water inlet filter has not become blocked by impurities
(see “Care and maintenance” chapter.)
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint-Ariston LFD 11M132 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LFD 11M132 in the language / languages: German, French as an attachment in your email.

The manual is 11,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hotpoint-Ariston LFD 11M132

Hotpoint-Ariston LFD 11M132 User Manual - English - 28 pages

Hotpoint-Ariston LFD 11M132 User Manual - Dutch - 76 pages

Hotpoint-Ariston LFD 11M132 User Manual - Italian - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info