Manual Hotpoint-Ariston LFD 11M132 (page 26 of 84) (German, French)

570818

Zoom out

Zoom in

1/84

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

(Follow the instructions given on the packaging).

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs off

the surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

• WhentheLOWRINSEAIDindicatorlight* on the control panel

is illuminated, a reserve supply of rinse aid is still available

for1-2cycles;

1.Openthedispenser“D” by pressing and pulling up the tab

on the lid;

2.Carefullyintroduce the rinse aidasfar as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Rinse-aid dispenser setting

If you are not completely satisfied with the drying results, you

canadjustthequantityofrinseaid.Switchonthedishwasher

usingtheON/OFFbutton,presstheSettingsbuttonandaccess

the menu “Rinse-aid dispenser setting” using the buttons next

to the grey arrows. The set level appears on the display

(the

defaultrinse-aidsettingislevel2.)

Choose the desired level and press the OK button to save the

setting. To exit the function wait a few seconds, press the ESC

buttonorswitchoffthemachineusingtheON/OFFbutton.

If the rinse aid level is set to ZERO, no rinse aid will be supplied.

TheLOWRINSEAIDindicatorlightwillnotilluminateifyourun

out of rinse aid.

Up to maximum 4 levels can be set based on the dishwasher

model.

• Iftherearestreaksonthecrockery,settheadjustmentdevice

toalowernumber(1-2.)

• Ifthereare drops of water or limescale marks, set the

adjustment device to a higher number (3-4.)

Setting the water hardness

Everydishwasherisequippedwithawatersoftenerwhich,by

using refined salt designed specially for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from your local water supplier.

SwitchonthedishwasherusingtheON/OFFbutton,pressthe

Settings button and access the menu “Water hardness” using

the buttons next to the grey arrows. The set level appears on the

display

(the default water softener setting is level 3.)

Use the buttons next to the grey arrows to select the desired

level

(1-2-3-4-5* see Table on water hardness)

up to maximum

5 levels. Press the OK button to save the setting.

- To exit the function wait a few seconds, press the ESC button

orswitchoffthemachineusingtheON/OFFbutton.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refined salt removes limescale from the water, thus avoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• Whenthegreenfloat* cannot be seen by simply looking at

the cap of the salt dispenser;

• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel

is illuminated *;

1.Removethelowerrackandunscrewthe

cap (anticlockwise).

2.Thefirsttimeyoudothis:fillthewater

tank right up to its edge.

3. Position the funnel

(see figure)

and

fill the salt dispenser up to the edge

(approximately1kg).Itisnormalforalittle

water to leak out.

4. Remove the funnel* and wipe any salt residues away from

the opening; rinse the cap under running water and then screw

it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped arrangement) in the lower part of

the cap (cap with green float

*).

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whennecessary,measureoutthesaltbeforeawashcycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt dispenser

capacity duration

level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1,1 - 2 5 months

3 12 - 17 21 - 30 2,1 - 3 3 months

4 17 - 34 31 - 60 3,1 - 6 2 months

34 - 50 61 - 90 6,1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the use of salt.

* a setting of 5 may increase cycle duration.

** 1 wash cycle per day.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston LFD 11M132 in the language / languages: German, French as an attachment in your email.

The manual is 11,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hotpoint-Ariston LFD 11M132

Hotpoint-Ariston LFD 11M132 User Manual - English - 28 pages

Hotpoint-Ariston LFD 11M132 User Manual - Dutch - 76 pages

Hotpoint-Ariston LFD 11M132 User Manual - Italian - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston LFD 11M132 Manual

Product: