Manual Hot Spring JETSETTER - JJ (page 4 of 48) (English)

624654

Zoom out

Zoom in

1/48

Page 1

Safety Information

Safety InformatIon

IMPORTANT SAFETY

INSTRUCTIONS

(READ AND FOLLOW ALL

INSTRUCTIONS)

AVOIDING THE RISK TO CHILDREN

DANGER - RISK OF CHILD DROWNING

Extreme caution must be exercised to prevent unauthorized access

by children. To avoid accidents, ensure that children cannot use a spa

unless they are supervised at all times.

WARNING

To reduce the risk of injury, do not permit children to use this spa unless

they are closely supervised at all times.

• To reduce the risk of injury, lower water temperatures are

recommended for young children. Children are especially sensitive to

hot water.

• Extreme caution must be exercised to prevent unauthorized access

by children. To avoid accidents, ensure that children cannot use a spa

unless they are supervised at all times.

DO:

• Make sure you always lock the child resistant locks after using the spa

for your children’s safety. Every HOT SPRING spa is equipped with

a locking cover that meets the ASTM F1346-91 Standard for Safety

Covers.

• Test the water temperature with your hand before allowing children to

enter the spa to be sure that it’s comfortable. Children are especially

sensitive to hot water.

• Remind children that wet surfaces can be very slippery. Make sure

that children are careful when entering or exiting the spa.

DON'T:

• Allow children to climb onto the spa cover.

• Allow children to have unsupervised access to the spa.

AVOIDING THE RISK OF ELECTROCUTION

DANGER - RISK OF ELECTROCUTION

• Connect only to a grounded source.

• Do not bury the power cord. A buried power cord may result in death,

or serious personal injury due to electrocution if direct burial-type cable

is not used, or if improper digging occurs.

• A ground terminal (pressure wire connector) is provided on the control

box inside the unit to permit connection of a minimum No. 8 AWG

(8.4 mm²) solid copper bonding conductor between this point and

any metal equipment, metal water pipe, metal enclosures of electrical

equipment, or conduit within five feet (1.5 m) of the unit as needed to

comply with local requirements.

• Do not operate the audio main controls while inside the spa (if spa is

equipped with an audio component).

• Do not connect any auxiliary components (for example, cable

additional speakers, headphones, additional audio components) to the

audio system unless approved by Watkins Manufacturing Corporation .

• Do not self service audio component by opening spa door as this may

expose dangerous voltage or other risk of injury. Refer all servicing to

qualified service personnel.

• Do not attach an external antennae to a spa audio system unless

installed by a licensed electrician in accordance with Article 810 of the

National Electric Code, ANSI/NFPA 70.

WARNING

• To reduce the risk of electrical shock, replace a damaged cord

immediately. Failure to do so may result in death or serious personal

injury due to electrocution.

• Your spa is provided with a Ground Fault Circuit Interrupter (GFCI)

for user and equipment protection. To ensure proper operation of this

important safety device, test according to the following instructions per

electrical configuration.

• Cord-Connected 115 volt, 20 amp models: The GFCI is located at

the end of the power cord. Before each use, with the unit operating,

push the TEST button. The unit should stop operating and the GFCI

power indicator will go out. Wait 30 seconds and then reset the GFCI

by pushing the RESET button. The GFCI power indicator will turn

on, restoring power to the spa. If the interrupter does not perform in

this manner, there may be an electrical malfunction and with it, the

possibility of an electric shock. Disconnect the power until the problem

has been corrected.

• 230 volt, permanently installed or converted models:

• A ground terminal is provided on the terminal block (TB-1, system

ground terminal) located inside the control box. To reduce the risk

of electric shock, connect this terminal to the grounding terminal

of your electrical service or supply panel with a continuous green,

insulated copper wire. The wire must be equivalent in size to the

circuit conductors supplying the equipment. In addition, a bonding

terminal (pressure wire connector) is provided on the outside of

the control box for bonding to local ground points. To reduce the

risk of electric shock, this connector should be bonded with a No.

8 AWG (8.4 mm

) solid copper wire to any metal ladders, water

pipes, or other metal within 5 feet (1.5 m) of the spa to comply with

local requirements. The means of disconnection must be readily

accessible, but must be installed at least 5 feet (1.5 m) from the

spa.

• Your spa is provided with a suitably rated circuit breaker to open all

ungrounded supply conductors.

• Your spa uses ground fault circuit interrupters in the electrical

subpanel. Before each use of the spa and with the unit operating,

push the TEST button on each breaker. The switch should click

over to the “Trip” position. Wait 30 seconds and reset each GFCI

breaker by switching it completely off and then completely on.

The switch should then stay on. If either of the interrupters does

not perform in this manner, it is an indication of an electrical

malfunction and the possibility of an electric shock. Disconnect the

power until the fault has been identified and corrected.

IMPORTANT: Failure to wait 30 seconds before resetting the GFCI

may cause the spa’s Power Indicator (on the control panel) to blink. If

this occurs, repeat the GFCI test procedure.

I apologise, but it not absolutely approaches me.
Submitted on 27-10-2022 at 01:49
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hot Spring JETSETTER - JJ in the language / languages: English as an attachment in your email.

The manual is 6,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hot Spring JETSETTER - JJ Manual

Product: