538730

Hormann Schuifhekaandrijving Manual

22
Zoom out
Zoom in
Previous page
1/132
Next page
2.3 Safety instructions for fitting
WARNING
Incorrect attachment of control devices
Incorrectly attached control devices (e.g.
buttons) may trigger unwanted gate travel.
Persons or objects may be trapped as a
result.
Fit permanently installed control devices f
(such as buttons, etc.) within sight of the
gate, but away from moving parts.
Install control devices at a height of at f
least 1.5 m (out of the reach of children).
Observe the following points during fitting:
The fitter must ensure that the national regulations •
governing the operation of electrical equipment are
complied with.
Before fitting the operator, make sure that the gate can •
also be easily operated manually. Use on gates with a
gradient or slope is impermissible.
Prior to installation, immobilize any mechanical locks not •
needed for power operation of the sliding gate. This
includes in particular any locking mechanisms connected
with the gate lock.
In addition, check the entire gate system (gate pivots, •
bearings and fastenings) for wear and possible damage.
Check for signs of rust, corrosion or fractures.
The applicable regulations regarding occupational safety •
must be complied with when carrying out the fitting work.
Always cover the operator before drilling, since drilling •
dust and shavings can lead to malfunctions.
After fitting has been completed, the installer of the gate •
system must declare conformity with DIN EN 13241-1 in
accordance with the scope of application.
Safety instructions for operation2.4
WARNING
Danger of injury during gate travel
Persons or objects may be trapped while the
gate is closing.
Make sure that no persons or objects are f
in the gate's travel range.
Make sure that children are not playing f
near the gate system.
Safety instructions for maintenance2.5
The sliding gate operator is maintenance-free. For your •
own safety, however, we recommend having the gate
system checked by a specialist in accordance with the
manufacturer's specifications.
All safety and protective functions must be checked •
monthly to ensure that they are in working order. Any
malfunctions and/or defects must be rectified
immediately if necessary.
Inspection and maintenance may only be carried out by a •
qualified person. Contact your supplier for this purpose.
A visual inspection may be carried out by the owner.
Contact your supplier in the case of necessary repairs. •
We would like to point out that any repairs not carried out
properly or with due professionalism shall render the
warranty null and void.
Notices on illustrated section2.6
The illustrated section shows the operator attached to the
inside right of a closed sliding gate. Where installation or
programming for a sliding gate differs because the operator is
attached to the inside left of a closed sliding gate, this is
shown in addition.
Several figures also contain the symbol below with a text
reference. These references to specific texts in the ensuing
text section provide you with important information regarding
fitting and operation of the sliding gate operator.
Example:
2.2
See text section, Chapter 2.2
In addition, in both the text section and the illustrated section
at the points where the DIL switches to set the controls are
explained, the following symbol is shown.
This symbol indicates the factory setting(s) of
the DIL switches.
Definitions3
Hold-open phase
Waiting phase at the OPEN end-of-travel position before the
gate closes during automatic timed closing
Automatic timed closing
Automatic timed closing of the gate after a set time has
elapsed and after reaching the OPEN end-of-travel position.
DIL switches
Switches on the control print for setting the control.
Through-traffic photocell
When the gate is passed through, the photocell stops the
hold-open phase and resets it to a preset value.
Impulse control
A sequence of impulses which allows the gate to alternately
OPEN-STOP-CLOSE-STOP.
22
TR10A059-C RE / 10.2008
ENGLISH
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hormann Schuifhekaandrijving at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hormann Schuifhekaandrijving in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info