606951

Horizon Hobby DX4C Transmitter Manual

11
Zoom out
Zoom in
Previous page
1/21
Next page
11
Spektrum DX4C • tranSmitter inStruCtion manual
EN
EXPO
The Exponential (Expo) function affects the response rate of the
steering, throttle and/or brake. A positive Steering Expo value, for
example, decreases steering sensitivity around neutral to make it
easier to drive at high speeds in a straight line while still allowing
for maximum turning radius. While sensitivity with positive Expo
is decreased around neutral, it increases the sensitivity near the
end of travel.
*Reference chart for options available for each channel:
A Channel
B L (left)*
C R (right)*
D Box shows around selected text
E Adjustable value (from -100% to +100%
(0 is factory default or inhibit))
Channel Top Bottom
Steering L (left) R (right)
Throttle B (brake) F (forward)
D
E
B
A
C
Binding the Transmitter and Receiver
In order to operate, the receiver must be bound to the
transmitter. Binding is the process of programming the receiver
to recognize the GUID (Globally Unique Identifier) code of a single
specific transmitter. When areceiver is bound to atransmitter/
model memory, the receiver will only respond to that specific
transmitter/model memory.
Binding and Calibrating the Receiver
(AVC Receivers Only)
You must calibrate the receiver each time it is placed in bind
mode.
IMPORTANT: The following sequence of steps must be
followed in order for AVC to function properly.
1. Insert the Bind Plug in the BIND port on the receiver.
2. Power on the receiver. The orange LED flashes, indicating
the receiver is in bind mode.
3. Center the ST TRIM and TH TRIM on the transmitter.
4. Put your transmitter in bind mode.
5. The bind process is complete when the orange LED on the
receiver is solid.
6. Pull the transmitter trigger to Full Throttle.
7. Push the transmitter trigger to Full Brake, then return the
trigger to center.
8. Turn the transmitter steering wheel to Full Right.
9. Turn the transmitter steering wheel to Full Left, then return
the steering wheel to center. The orange LED flashes once.
10. Remove the bind plug once the calibration and binding
process is complete.
11. Power off the transmitter.
IMPORTANT: You must rebind the transmitter and receiver
if you:
•
Change the servo reverse after binding
•
Change the travel after binding
•
Want to use the receiver with a different model memory
If you change the servo reversing or travel adjust after binding,
AVC will not work properly.
Disabling the Stability Assist Function
If you participate in organized racing, you may be required to turn
AVC technology off. To turn off AVC technology, insert a second
Bind Plug in the Disable port before binding.
IMPORTANT: You must calibrate the receiver each time it is
placed in bind mode. To activate AVC, see the steps in BINDING
AND CALIBRATING THE RECEIVER.
E
B
C
A
D
A Select Bind when a receiver is prepared for binding.
B Active model number
C Active model name
D Mode
E Speed
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Horizon Hobby DX4C Transmitter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Horizon Hobby DX4C Transmitter in the language / languages: English as an attachment in your email.

The manual is 7,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Horizon Hobby DX4C Transmitter

Horizon Hobby DX4C Transmitter User Manual - German - 21 pages

Horizon Hobby DX4C Transmitter User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info