606950

Horizon Hobby AR7210BX - BeastX Manual

53
Zoom out
Zoom in
Previous page
1/59
Next page
EN
53
If the helicopter is not aligned horizontally as desired with active SAFE
®
technology, i.e drifts
to one side in hovering, the artificial horizon can be readjusted. This is done at Parameter
Menu Point A which also serves as servo trim function. If you activate SAFE
®
technology
at Parameter Menu Point Aviathetransmitter’sSAFE
®
technology channel, you switch to
trimming of the horizon instead of trimming the servos. By moving the aileron or elevator
stick the roll and pitch tilt of the horizon can be increased/decreased. Briefly touching the
appropriate stick will trim the horizon stepwise by 0.5 degrees to the specific direction.
Touching the stick repeatedly or holding it for longer time will trim the horizon by several
steps. The Status-LED indicates the trim values: when it lights in blue color both angles are
0 degrees resp. they are in the factory setting. If the Status-LED lights red one or both angles
are adjusted slightly. If the Status-LED is purple, then one axis is trimmed by more than 5.0
degrees. When the status LED goes out, one of the two axes is further trimmed than 10.0
degrees, which is the limit for each axis! By moving the rudder stick you can remove the trimm
that has been set since entering this menu point. Place the helicopter in horizontal position
and you should be able to see the effect of trimming. Note that the helicopter usually is slightly
tilted to the side in hovering flight due to the drag of the tail rotor. Therefore as a starting
point it is recommended to trim about 5 degrees to the right when using a helicopter with
clockwise turning main rotor. Also note that SAFE
®
technology cannot recognize the absolute
position of the helicopter. Depending on wind and environmental conditions it may happen
that the helicopter drifts slightly into a certain direction during hovering flight. Also long-
lasting vibration or fluctuations in temperature can cause the helicopter not always comply
exactly the same attitude. Therefore, only trim in moderate steps and only when the helicopter
reproducible drifts to the same direction!
Parameter Menu Point A is used to adjust two different things: Trimming the servo center
positions and trimming the SAFE
®
technology horizon. Depending on whether SAFE
®
technology is activated or not, either the artificial horizon or the servo center positions can
be trimmed. The Status LED provides information on the currently active trim mode. If the
Status-LED is lit permanently, the servo center positions are trimmed. If the Status-LED
flashes, SAFE
®
technology is turned on and the artificial horizon can be trimmed.
When using SAFE
®
technology in “Flight trainer mode,” the tilt angle directly depends on the
transmitter’ssignallengthandthereforevariesdependingonthetransmittertype.Youcan
fine tune the maximum angle by simply increasing or reducing the maximum deflection of
your control stick(s) in the transmitter by using the Dual Rate function. You could even switch
between different angles in flight. Also you can adjust the maximum tilt angle by using the
StudioX software and the optional USB2SYS (SPMA3030 or BTXA76007) interface.
… 53 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Horizon Hobby AR7210BX - BeastX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Horizon Hobby AR7210BX - BeastX in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Horizon Hobby AR7210BX - BeastX

Horizon Hobby AR7210BX - BeastX User Manual - English - 176 pages

Horizon Hobby AR7210BX - BeastX User Manual - German - 64 pages

Horizon Hobby AR7210BX - BeastX User Manual - German - 176 pages

Horizon Hobby AR7210BX - BeastX User Manual - French - 57 pages

Horizon Hobby AR7210BX - BeastX User Manual - French - 176 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info