723849

Honeywell HT-9004C Manual

3
Zoom out
Zoom in
Previous page
1/11
Next page
WALL MOUNTING
(HT-800 Series and HT-900 Series Only)
• Locate and mark the position on the wall where the fan will be mounted (preferably at a wall stud).
• Insert two screws into the wall stud. (Screws are not included and can be purchased at a
hardware store)
• Use #8, 1” length screws, leave 3/8” below screw head (bolt) exposed from the wall.
• Line up the openings on the base of the fan with the screws (bolts) and hang the fan on the wall.
NOTE: HF-910 Series and HT-908 Series cannot be wall-mounted
CLEANING AND STORAGE
Unplug the fan before cleaning.
• These fans are equipped with a cord wrap feature for storage on the bottom of
the fan (Fig. 7).
• Use only a soft, damp cloth to gently wipe the fan clean.
• DO NOT immerse the fan in water and never allow water to drip into the motor
housing.
• DO NOT use gasoline, paint thinner or other chemicals to clean the fan
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
REMOVAL OF THE FRONT GRILLE FOR CLEANING
DO NOT remove the fan grille unless the power is turned off and the
power cord is unplugged.
• Gently lay the fan face down on a table (Fig. 8).
• Screws are located in the holes around the back grille of the fan (Fig. 9).
• After the screws in each hole are located, insert a standard Phillips Head
screw driver into one of the screw holes.
NOTE: Screwdriver head should fit comfortably in the hole without being
too tight or leaving too much room. A screwdriver with a head that is too
small will have trouble engaging the screw.
• Each screw should be engaged and loosened by unscrewing each head
to the left.
• Once all screws have been loosened, slowly lift the fan up off the surface using
the back carrying handle, and separate the front grille along the seam where
the screws were located (Fig. 10).
NOTE: Screws will sometimes fall out of the back of the unit once loosened,
so be sure not to stand the fan up or tip it over too quickly.
• To reassemble the fan, collect all of the screws and lay the fan on its back
(Fig. 11).
• Place the front grille onto the unit, lining up the notch in the grille, with the
notch along the bottom of the fan (Fig. 12).
• Once the grille is aligned with the body of the fan, and each screw hole
matches up, flip the unit to lay it face down on a flat surface.
• Insert each screw into a hole and gently tighten each screw. Ensure that the
front grille and the bottom of the fan are tightly secured together.
• For storage, clean the fan carefully as instructed. Store the fan in the original
packaging or cover the product to protect it from dust.
OPERATION
• Be sure the fan is in the OFF position.
• Place your fan on a dry, level surface.
• Plug the power cord into a polarized 120 volt AC wall outlet.
• To operate, turn the control knob to the desired fan speed: HIGH (III), MEDIUM
(II) or LOW (I) (Fig. 5).
• Adjust the fan to the desired angular air output direction.
• To move the fan, turn the fan OFF and pick it up by the concealed handle
that is located on the outside rim of the fan (Fig. 6).
Fig. 5
Fig. 6
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell HT-9004C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell HT-9004C in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info