554935
96
Zoom out
Zoom in
Previous page
1/122
Next page
88
Galaxy 2 Series Installation Manual
10 = Line Fail
This option has two settings:
0 = No
When set to No there is no internal alarm or indication in the event of a telephone line fail condition.
1 = Yes
If this option is set to Ye s, a line fail condition will cause a fault condition. An alert indication is given in the
unset state. A Line Fail condition does not exist until 30 seconds after loss of line voltage. A line fault indication
will then be given within 10 seconds if the debounce time is set to zero. However, this delay can be increased
to between 1 and 60 minutes by altering the debounce time. This is to cope with expected performance levels
of different telephone networks.
On selecting 1 = Yes a further sub-option becomes available:
1 = Debounce Time
The debounce time determines the response time before a line fail condition registers. It can be set from 0-60
minutes.
The audible indication of the line fail is cancelled by the entry of a valid user code but the Line Fail display
remains until 30 seconds after the Line Fail condition is restored.
The communicator still attempts to dial out in the event of an alarm, even if a Line Fail condition has been
detected.
11 = Fail to Comm
This option sets the comms fail time window. This is defaulted to 120 seconds. If the panel does not receive a
valid kiss-off signal from the Alarm receiver in this time, a Comms fail condition will occur, to indicate that the
message did not get through to the receiver. The panel will continue to attempt to send the signal for a further
period equal to the programmed window before giving up on that signal altogether.
The programmable range for Fail to Comm is 0 to 244 seconds.
12 Remote Access
This option defines when and how remote servicing will operate. The options are described as follows.
1 = Access Period
This option determines under what conditions the remote site can be accessed by the remote operator. There
are three modes:
0 = Full
Access available at any time.
1 = When Unset
Access only when all the groups are unset.
2 = No Unsetting
Remote servicing software can gain access to system when set but cannot unset the system remotely.
56 - Comms (cont’d)
96


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Galaxy 2 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Galaxy 2 Series in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell Galaxy 2 Series

Honeywell Galaxy 2 Series User Manual - Dutch - 20 pages

Honeywell Galaxy 2 Series Usermanual and installation guide - Dutch - 148 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info