471572
11
Zoom out
Zoom in
Previous page
1/12
Next page
Installation Guide 11
6) Trouble Shooting
6.1 Trouble Shooting Guide
Symptom (Fault
Message)
Possible Cause Remedy
The room thermostat
displays the
symbol but
the relay box relay does not
switch on.
This is normal operation. The relay box cycles
the relay on and off for times proportional to
the demand signal (0-100%) from the room
thermostat. The
symbol only indicates that the
demand value is greater than 0%.
Using the
button change the
temperature setpoint by a few degrees.
The relay box should switch the relay on
after a few seconds delay.
The relay box does not
react to setpoint changes
on the room thermostat.
The room thermostat and relay box are not
bound.
Reset the relay box by pressing and
holding the push button for 15 seconds.
Then follow the binding / rebinding
procedure as described in section 5)
Additional Installation Information.
After the binding procedure
the red LED is on and the
green one is flashing once
every 3 sec on the relay
box.
Incorrect or incomplete binding procedure.
Incorrect position of the room thermostat during
binding.
Repeat the binding procedure.
Repeat the binding procedure keeping
approx. 1 m distance between the relay
box and the room thermostat.
The red LED on the
relay box is illuminated
(Communication loss)
The relay box receives no RF messages from the
room thermostat:
RF signal is blocked due to wrong location of the
room thermostat.
Room thermostat batteries are exhausted.
Re-locate the room thermostat following
instructions in section 2) Installing the
CM700 Wireless System.
Replace batteries in the room thermostat.
6.2 Diagnostic Mode
The CM727/721 room thermostat has a user accessible mode that provides information useful to a remote
service person and a means of checking whether the boiler is working. To access this press the OFF
button, then press and hold the button for 5 seconds. The room thermostat will enter the user settings
mode. Next press and hold the and buttons together. The room thermostat will hold the relay on for
5 minutes and the following information can be viewed on the display by pressing the or button. :
model ID, date code (WW/YY) & checksum.
11


Need help? Post your question in this forum.

Forumrules
1

Forum

honeywell-cm721

Reset search

  • Green light on red light flashing box next to boiler why .
    Thank youb Submitted on 6-4-2022 at 21:00

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell CM721 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell CM721 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell CM721

Honeywell CM721 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info