478012
8
Zoom out
Zoom in
Previous page
1/18
Next page
8 EN
WITH 3-TOOTH AND 4-TOOTH
BLADE
CAUTION:
Do not use a blade larger than
255 mm in diameter.
CUTTING
The 3-tooth and 4-tooth grass-
cutting blade is especially
suitable for clearing dense and
tangled weeds, bushes such as
brambles or wild shrubs with a
stem diameter of less than 2 cm.
To trim bushes, lower the cutting
attachment from above while
holding it horizontal so as to cut
the branches in small pieces.
It is dangerous to use grass-
cutting blades on very hard
wood and/or plants with a
large stem diameter. Kicking
of the cutting attachment is
difficult to control, and can seriously endanger the operator
and cause serious damage to the equipment.
WITH CIRCULAR SAW BLADE
Use of the circular saw blade is only authorized on UMK435E1
of type UEET.
CAUTION:
Never use a saw blade with a diameter in excess of 200 mm. The
circular saw blade is intended to be used for cutting out shrubs,
bushes and small trees whose trunk does not exceed 6 cm in
diameter.
CUTTING
Some blade sectors [1] must
not be used as they will cause
the tool to rebound owing to
the direction of rotation.
Tools fitted on Honda
brushcutters rotate
counterclockwise. It NEVER
cut with the right half of the
blade. The part to be used is represented by the grey area.
For the best results, you must swing your equipment quickly
towards the branch or trunk to be cut. Do not proceed gradually as
engine speed could drop and lead to stalling.
Estimate the height of the items to be cut and where they might
fall.
Ensure that falling pieces will not cause bodily injuries to
persons or property damage.
Make sure the blade is not stuck in the trunk when it falls.
Always cut on the side opposite the fall.
MAINTENANCE
REPLACING THE LINE
1. Press the lugs [2] located on either side of
the head to open it.
2. Extract the reel and remove
the rest of the nylon line.
3. Prepare 3 metres of 2.7 mm
diameter line and fold it in
half, lengthwise.
4. Place the middle of the line in
the notch [5] in the reel and
coil the wire by turning in the
specified direction.
5. Secure the ends in the two
opposite notches [3] (leaving
an excess of 10 cm of line).
6. Reinstall the reel in its place
and feed the lines through
the two side holes [4].
7. Reinstall the cover.
CAUTION:
Always use a line of the
diameter recommended in the
technical specifications.
Poor results would be
obtained if the line diameter is
too large as this will result in
an excessive load on the
engine, so reducing its
performance.
Never replace the nylon line with a line of a different material,
such as steel wire.
To avoid severe personal injury, disconnect the spark plug cap
to prevent accidental starting.
Wear heavy gloves to prtect yur hands when replacing the
nylon head.
SHARPENING
3-TOOTH AND 4-TOOTH BLADES
Sharpening is essential to obtain good results. A slightly blunt
cutting attachment can be sharpened with a file.
A grinding wheel should be used if the wear is more severe.
CAUTION:
In all cases, the cutting attachment must be kept correctly
balanced. If you do not have the required tools or if you think your
cutting attachment may not be properly balanced, contact your
authorized Honda dealer.
Remove the cutting attachment for sharpening and check that it is
not cracked, out of true or bent.
If it is, replace it with a new one.
SAFETY
C13
D2 D3
3
2
1
SAFETY
C13
D2 D3
[1]
C11B8
SAFETY
[3]
[2]
[4]
[5]
SAFETY
C13 D2 D3
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda UMK425E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda UMK425E in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda UMK425E

Honda UMK425E User Manual - English - 88 pages

Honda UMK425E User Manual - English - 58 pages

Honda UMK425E User Manual - German - 88 pages

Honda UMK425E User Manual - German - 58 pages

Honda UMK425E User Manual - German - 18 pages

Honda UMK425E User Manual - Dutch - 88 pages

Honda UMK425E User Manual - Dutch - 18 pages

Honda UMK425E User Manual - French - 88 pages

Honda UMK425E User Manual - French - 58 pages

Honda UMK425E User Manual - Italian, Spanish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info