478012
7
Zoom out
Zoom in
Previous page
1/18
Next page
7 EN
HOT START
The machine is considered to be "hot" if the engine has been
running for more than 5 minutes in the 10 minutes before starting
up.
The hot start procedure is the same as the cold start procedure
except that the choke [1] is not needed. (The lever must be left in
the low position).
NOTE:
Should you have difficultie store-start a hot engine, follows
this procedure:
1. Turn the engine to the OFF position (O).
2. Make sure that the choke lever is in OPEN position.
3. Keep the throttle control lever (throttle trigger) fully squeezed.
4. Pull the starter grip 3 to 5 times, and release the throttle control
lever (throttle trigger).
5. Start the engine referring to the procédures described above.
CAUTION:
Be sure to turn the engine switch to the OFF position (O).
If this operation is executed with the engine switch at the ON
position, the blade may rotate when the engine starts and a
personal injury may result.
STOPPING THE ENGINE
1. To stop the engine, press the Start/Stop button to engage the
Stop position (O) [2].
2. This step can also be taken to stop the machine in case of
emergency.
Note that the cutting attachment continues turning by inertia
after the engine has been stopped.
OPERATION
OPERATING POSITION
Once the machine has been started,
attach it to the harness as already
described in the section on preparation.
When handling the machine, take care to avoid striking any
objects with the cutting attachment and keep the cutting
attachment away from your body. Do not use the machine
unless it is attached to the harness.
Hold the brush cutter firmly by both grips as shown. Always keep
firm footing on both feet when working. Take appropriate breaks
and vary your working position.
CAUTION:
When using the machine, always allow the engine to idle between
operations. If the machine is allowed to run at maximum speed
with no load (no resistance on the cutting attachment) for long
periods, the engine may be seriously damaged.
WITH NYLON LINE TYPE CUTTING
HEAD
This attachment is designed to complete the job
done with a lawnmower. It is especially handy
and efficient for cutting grass along walls or
fences, around trees or posts and on narrow or uneven surfaces
where a lawnmower cannot be used.
Make sure the line cutting blade is properly mounted on the
cutting attachment guard.
LINE LENGTH ADJUSTMENT
At maximum rotating speed, gently press the nylon line cutting head
on the ground. The line is automatically extended. Repeat this
operation until the optimal length is obtained.
When the engine is started and the cutting attachment starts
rotating, the excess line will automatically be cut by the line cutter
located on the guard.
CUTTING
The nylon line cuts grass cleanly without damaging tree bark and
avoiding the violent impacts that would occur between a rigid cutting
attachment and hard surfaces.
It is, however, recommended not to work too long in such areas in
order to avoid damaging fragile, immature plant, in particular, and to
avoid premature line wear.
Proceed in stages, when trimming, tilting the cutting attachment
slightly.
For larger areas, hold the cutting attachment horizontal and sway it
sideways from right to left and from left to right, alternately.
[1]
[2]
[2]
SAFETY
Read the
safety
instructions
SAFETY
A4 C11
3
2
1
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda UMK425E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda UMK425E in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda UMK425E

Honda UMK425E User Manual - English - 88 pages

Honda UMK425E User Manual - English - 58 pages

Honda UMK425E User Manual - German - 88 pages

Honda UMK425E User Manual - German - 58 pages

Honda UMK425E User Manual - German - 18 pages

Honda UMK425E User Manual - Dutch - 88 pages

Honda UMK425E User Manual - Dutch - 18 pages

Honda UMK425E User Manual - French - 88 pages

Honda UMK425E User Manual - French - 58 pages

Honda UMK425E User Manual - Italian, Spanish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info