580909
18
Zoom out
Zoom in
Previous page
1/22
Next page
18
ENGLISH
Blade Removal
1. HXEA: Put the throttle lever in the STOP position.
HMEA: Turn the key to the OFF position.
2. Turn the fuel valve OFF. Disconnect the spark plug cap, then tilt
the mower to the right side, so the air cleaner side is up. This will
help to prevent fuel leakage and hard starting due to carburetor
flooding.
3. Use a 14 mm (6 point) socket wrench and remove the two blade
bolts [1] and special washers [2] from the blade control assembly
[5]. Use a wooden block to prevent the blades from turning when
removing the bolts.
4. Remove the upper [4] and lower blades [3].
Blade Installation
1. Clean dirt and grass from around the blade mounting area. Install
the blades [3] and [4] using the two blade bolts [1] and special
washers [2] as shown.
Be sure to install the special washers with the concave side toward
the blades and the convex side toward the head of the bolt.
The blade bolts are specially designed for this application and
must not be replaced with other bolts.
2. Tighten the blade bolts with a torque wrench [7]. Use a wooden
block [6] to prevent the blades from turning.
Blade bolt torque: 49 ~ 59 N·m
If you do not have a torque wrench, have an authorized Honda
dealer tighten the blade bolts before you use the mower. If the
blade bolts are overtightened, they could break. If the blade bolts
are not tightened enough, they could loosen or come out. In either
case, it would be possible for the blades to fly off while you are
operating the mower.
GRASS BAG CLEANING AND REPLACEMENT
Cleaning
Wash the bag with a garden hose, and allow it to dry completely
before use; a wet bag will clog quickly.
Replacement
Replace a worn or damaged bag with a Honda replacement bag or its
equivalent.
Removal
1. Unclip the plastic edges [1]
of the bag [2] from the
frame [3].
2. Remove the bag from the
frame.
Installation
1. Insert the bag frame [3] into the
bag [2], as shown above.
2. Clip the plastic edges [1] of the
bag onto the frame.
SPARK ARRESTER SERVICE
The spark arrester must be serviced every 100 hours to keep it
functioning as designed.
1. Allow the engine to cool, then remove the three bolts [1] from the
muffler shield [2] using a 10 mm socket wrench.
2. Remove the muffler shield [2].
3. Remove the screw [4].
4. Remove the spark arrester [3] from the muffler [5].
5. Check for carbon deposits on the spark arrester and the exhaust
port. Brush carbon deposits away. Be careful to avoid damaging
the spark arrester screen.
6. Install the spark arrester in the muffler.
7. Install the muffler components on the engine, and tighten the three
bolts securely.
[1]
[2]
[3]
[4]
[5]
[3] [4]
[1]
[2]
[7]
[6]
[1]
[3]
[2]
[1]
[5]
[4]
[2]
[3]
[1]
HXE.book Page 18 Monday, August 6, 2007 10:44 AM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda HRX537 HMEA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda HRX537 HMEA in the language / languages: English as an attachment in your email.

The manual is 4,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info