477990
15
Zoom out
Zoom in
Previous page
1/56
Next page
ENGLISH 15
BLADE REMOVAL AND INSTALLATION
If you remove the blade for sharpening or replacement, you will need
a torque wrench for installation. Wear heavy gloves to protect your
hands.
BLADE SHARPENING: To avoid weakening the blade, or causing
imbalance or poor cutting, the blade should be sharpened by trained
staff at an authorized Honda dealer.
BLADE REPLACEMENT: Use a Honda Genuine replacement blade
or its equivalent.
Blade Removal
1. Turn the fuel valve OFF. Disconnect the spark plug cap, and then
tilt the mower to the right side so that the air cleaner side is up.
This will help to prevent fuel leakage and hard starting due to
carburetor flooding.
2. Use a 14 mm (6 point) socket wrench and remove the two blade
bolts [1] and special washers [2] from the blade holder [3]. Use a
wooden block to prevent the blade from turning when removing the
bolts.
3. Remove the blade [4].
Blade Installation
1. Clean dirt and grass from around the blade mounting area. Install
the blade [4] using the two blade bolts [1] and special washers [2].
Be sure to install the special washers with the concave side toward
the blade and the convex side toward the head of the bolt.
The blade bolts are specially designed for this application and
must not be replaced with other bolts.
2. Tighten the blade bolts with a torque wrench. Use a wooden block
to prevent the blade from turning.
Blade bolt torque: 49 ~ 59 N·m
If you do not have a torque wrench, have an authorized Honda
dealer tighten the blade bolts before you use the mower. If the
blade bolts are overtightened, they could break. If the blade bolts
are not tightened enough, they could loosen or come out. In either
case, it would be possible for the blade to fly off while you are
operating the mower.
TROUBLESHOOTING
ENGINE WILL NOT START
LOSS OF POWER
VIBRATION
[1]
[2]
[3]
[4]
[2]
[4]
[3]
[1]
Possible Cause Correction
Fuel valve OFF Turn the fuel valve ON (page 4).
Throttle lever in the wrong
position
Move the throttle lever to the CHOKE
position, unless the engine is warm.
(page 4).
Out of fuel Refuel (page 6).
Bad fuel; mower stored without
treating the gasoline, or refueled
with bad gasoline
Refuel with fresh gasoline (page 6).
Spark plug faulty, fouled, or
improperly gapped
Gap or replace the spark plug
(page 14).
Spark plug wet with fuel (flooded
engine)
Dry and reinstall the spark plug. Start
the engine with the throttle in the FAST
position.
Fuel filter clogged, carburetor
malfunction, ignition malfunction,
valves stuck, etc.
Take the mower to an authorized
Honda servicing dealer or refer to the
shop manual for repair.
Possible Cause Correction
Throttle not set to FAST Move the throttle to FAST (page 8).
Grass is too tall to cut Raise the cutting height (page 7), cut a
narrower swath, or cut more frequently.
Mower deck is clogged Clean out the mower deck (page 10).
Air cleaner is clogged Clean or replace the air cleaner
(page 13).
Bad fuel; mower stored without
treating the gasoline, or refueled
with bad gasoline
Refuel with fresh gasoline (page 6).
Fuel filter clogged, carburetor
malfunction, ignition malfunction,
valves stuck, etc.
Take the mower to an authorized
Honda servicing dealer or refer to the
shop manual for repair.
Possible Cause Correction
Grass and debris lodged under
the mower deck
Clean out the mower deck (page 10).
Blade loose, bent, damaged, or
unbalanced by improper
sharpening
Tighten loose blade bolts (page 15).
If the blade is found to be bent or
damaged, take the lawn mower to an
authorized Honda servicing dealer for
inspection.
Mechanical damage, such as a
bent crankshaft
Take the mower to an authorized
Honda servicing dealer or refer to the
shop manual for repair.
00X39VG36410.book Page 15 Monday, November 16, 2009 1:01 PM
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda HRS536 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda HRS536 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 7,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda HRS536

Honda HRS536 User Manual - German, Dutch, Italian - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info