630639
13
Zoom out
Zoom in
Previous page
1/40
Next page
Page 9 — English
ASSEMBLY
INSTALLING THE FRONT HANDLE
See Figure 4.
Position the front handle as shown.
Depress the buttons on the handle and insert into the
frame. Press down on the handle until the button on the
handle clicks into place.
ASSEMBLING THE WHEEL/DRAG STAKE
ASSEMBLY
See Figure 5.
 Locate the axles, hitch pins, washers and wheels.
 Slide the wheel onto the axle.
 Place a washer on the outside of the wheel and slide to
rest against the wheel.
 Push the hitch pin into the hole on the end of the axle to
secure the wheel/drag stake assembly.
NOTE: The hitch pin should be pushed into the axle until
the center of the pin rests on top of the axle.
 Repeat with the second wheel.
INSTALLING THE WHEEL /DRAG STAKE
ASSEMBLY
See Figure 6.
Use the wheel/drag stake assembly to transport the unit to
and from the work area or when cultivating.
To install:
Remove the adjustment knob located at the back of the
tine shield.
Insert the wheel/drag stake assembly into the bracket at
the back of the tine shield. To place the wheels in a high
position, insert the knob in the first hole. For a lower wheel
position, insert the knob in the second or third hole.
Insert adjustment knob through holes in bracket, pass-
ing through desired hole in wheel/drag stake assembly,
to secure wheel/drag stake assembly at desired height.
Thread the adjustment knob into the nut and tighten, to
secure wheel/drag stake assembly.
INSTALLING THE TINES
See Figure 7.
The cultivator has four tines —two inner tines stamped B
and C, and two outer tines stamped A and D. For correct
operation of the unit, the tines must be installed in the cor-
rect orientation.
NOTE: The view of the gearbox for tine installation is from
the front of the cultivator.
Lean the unit back on its wheels so that the handlebar
rests on the ground.
Place tine C on the tine shaft to the left of the gear box.
The stamped side of the tine should face away from the
gear box.
Place tine B on the tine shaft to the right of the gear box.
The stamped side of the tine should face away from the
gear box.
Place a felt washer on each side of the tine shaft, and
slide to rest against the inner tines.
Place the outer tine stamped D on the left side of the tine
shaft. The stamped side should face in toward tine C.
Place the outer tine stamped A on the right side of the
tine shaft. The stamped side should face in toward
tine B.
NOTE: When installed correctly, the angled edge of the
tine blades should face the ground.
To secure the tines to the tine shaft, insert the hitch pin
into the holes located on either side of the tine shaft.
NOTE: The unit will not operate properly if the tines are
installed incorrectly. If you notice a problem with the cultivat-
ing operation of the unit, check for proper tine positioning.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Homelite UT46510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Homelite UT46510 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 7,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Homelite UT46510

Homelite UT46510 Quick start guide - English, French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info