30156
11
Zoom out
Zoom in
Previous page
1/23
Next page
11
In the GLIDACRO mode, ELEVON mixing is not available to you, however V-TAIL mixing is available, as is SW # 3 as a three-
position function switch for mixing Ailerons (CH 1 and CH 5), and Elevator (CH 2). All three channels may be mixed in this mode
to accomplish a number of functions. For example, a sport acrobatic plane may display adverse nose pitching when flaps are
deployed. By mixing elevator with the flap command, the pilot will automatically correct the plane, requiring less work. We will
discuss other possibilities in the ACROBATIC PROGRAMMING chapter of this manual.
Please review the switch assignments for the different model modes on page 7.
To select an alternative model mode, use the following procedure:
b. Stick Mode Change
Your System X radio can be converted to Mode I or Mode II stick styles, regardless of the factory set mode. Mode I has the
Throttle (Ch 3) and Aileron (Ch 1) on the right side stick with Elevator (Ch 2) and Rudder (Ch 4) on the left side stick. Mode II, the
most popular style in the United States, has the Aileron (Ch 1) and Elevator (Ch 2) on the right stick, while Throttle (Ch 3) and
Rudder (Ch 4) are on the left stick of the transmitter.
If you decide to change the transmitter from Mode I to Mode II, or vice versa, the procedure to make this change is as follows:
1. Depress and hold both UP and DN/TIMER keys and turn your transmitter ON.
2. To change model mode style, use the CUT/SAVE key to make selection.
3. Once you make your selection, turn transmitter OFF. Your new selection will appear when the
transmitter is turned back ON.
NOTE: If you have chosen the Mode I control configuration, the following transmitter changes will be necessary. The drawing
below shows where the changes are to be made. Please note that since the drawing shows the back of the transmitter, the
throttle is now on the right side of the picture, and you will want to move it to the left side of the picture.
a. Remove the transmitter battery
b. Move the copper Ratchet piece from (A) on right to (A)
on the left.
c. Add spring tension to (B) on the right side by turning the tension spring screw clockwise.
d. Loosen tension to (B)
on the left side by turning tension spring screw counter-clockwise.
e. Remove the spring limit bracket (C) from the right side and place it on the left side at position (C)
f. Reconnect the transmitter battery
1. Depress and hold both UP and DN/TIMER keys and turn your transmitter ON.
2. Press either the UP or DN/TIMER key until display shows
St , or Stick Mode.
3. To change stick Mode style, use the CUT/SAVE key to make selection.
4. Once you make your selection, turn transmitter OFF. Selection is complete.
TENSION SPRING
TO CLOCKWISE
(B)
(C)
(A)
(A)
RATCHET COPPER
SPRING LIMIT
BRACKET
(C)
(B)
TENSION SPRING
TO CLOCKWISE
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitec FLASH_5SX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitec FLASH_5SX in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info