571421

Hitachi UG50Y Manual

14
Zoom out
Zoom in
Previous page
1/112
Next page
13
English
Examples of measuring using diff erent reference points
1
Measuring using front reference point (Fig. 7)
Place the front (reference point) of the instrument against the
measuring surface.
2
Measuring using rear reference point (Fig. 8)
Place the rear (reference point) of the instrument against the
measuring surface.
3
Measuring using the W1/4 socket hole (for the tripod) as the
reference point (Fig. 9)
Use the center of the socket hole for attaching the tripod as the
reference point.
NOTE
If the instrument needs to be level with the target, adjust the level using
the bubble tube. (Fig. 10)
5. Measuring procedures in each mode
NOTE
○
Check that there is nothing obstructing measurement by the laser.
○
Do not move the instrument during measuring (except during
continuous measurement).
○
The center of the laser beam is measured. The same applies when
the beam is aimed diagonally at the target.
○
The measuring range may vary depending on the characteristics of
the laser beam refl ected from the target surface or the surrounding
brightness.
To measure quickly and accurately outdoors in bright sunlight, use
a target plate (sold separately) or put the target in the shade.
○
Measuring errors may occur with transparent surfaces (such as
glass or water) or mirror surfaces, as well as in the case of surfaces
with holes in, uneven surfaces, diff erent temperatures and indirectly
refl ected light.
○
If the power is turned on and no button is pressed, the power will
turn off automatically after approximately 3 minutes. Press the
power button again to resume operation.
○
If the instrument is used and then left with no button pressed,
the laser will turn off after approximately 30 seconds. Press the
measure button again to resume operation.
○
The length of time after the power is turned on until the instrument is
ready to measure may vary depending on the usage environment.
○
If an error occurs while measuring, remedy the cause before
resuming measuring.
Measuring distance (Fig. 2, 6)
1
Select distance mode. (See “Selecting a measuring mode”)
2
Press the measure button and aim the laser beam at the target. The
status is indicated on the display.
3
Press the measure button again to stop measuring. A beep sounds
and the measurement is indicated on the display. When measuring
is fi nished, the laser goes off .
4
To continue measuring distance, repeat steps
2
and
3
.
The side button on the side of the instrument has the same function
as the measure button on the operation panel.
For convenient operation in narrow spaces, the instrument can be
placed in a vertical position.
Continuous measurement
Use continuous measurement to set the desired position from the
target.
1
Select continuous measurement mode. (See “Selecting a
measuring mode”)
2
Press the measure button and aim the laser beam at the target.
3
Move the instrument until the desired measurement is indicated on
the display.
4
Press the measure button again to fi nish continuous measurement.
The last measurement is indicated on the display.
Measurements are successively indicated on the display with a beep
sound every 0.5 to 3 seconds.
The previous measurement is deleted when the next measurement is
taken.
In continuous measurement mode, the power does not turn off
automatically. Be sure to press the power button after operation to end
continuous measurement.
000Book_UG50Y_WE.indb 13000Book_UG50Y_WE.indb 13 2009/08/20 13:48:092009/08/20 13:48:09
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi UG50Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi UG50Y in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info