389694

Hitachi sv 8 sa Manual

17
Zoom out
Zoom in
Previous page
1/21
Next page
15
English
GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas and bench-
es invite injuries.
2. Consider work area environment. Don’t expose
power tools to rain. Don’t use power tools in
damp or wet locations. Keep work area well lit.
Don’t use tool in presence of flammable liquids
or gases.
Power tools produce sparks during operation.
They also spark when switching ON/OFF. Never
use power tools in dangerous sites containing
lacquer, paint, benzine, thinner, gasoline, gases,
adhesive agents, and other materials which are
combustible or explosive.
3. Guard against electric shock. Prevent body contact
with grounded surfaces. For example; pipes, radia-
tors, ranges, refrigerator enclosures.
4. Keep children away. Do not let visitors contact
tool or extension cord. All visitors should be kept
away from work area.
5. Store idle tools. When not in use, tools should
be stored in dry and high or locked-up place out
of reach of children.
6. Don’t force tool. It will do the job better and safer
at the rate for which it was intended.
7. Use right tool. Don’t force small tool or attach-
ment to do the job of a heavy-duty tool. Don’t
use tool for purpose not intended-for example-
don’t use circular saw for cutting tree limbs or
logs.
8. Dress properly. Do not wear loose clothing or
jewelry. They can be caught in moving parts.
Rubber gloves and non-skid footwear are recom-
mended when working outdoors. Wear protective
hair covering to contain long hair.
9. Use safety glasses. Also use face or dust mask
if cutting operation is dusty.
10. Don’t abuse cord. Never carry tool by cord or yank
it to disconnect from receptacle. Keep cord from
heat, oil and sharp edges.
11. Secure work. Use clamps or a vise to hold work.
It’s safer than using your hand and it frees both
hands to operate tool.
12. Don’t overreach. Keep proper footing and balance
at all times.
13. Maintain tools with care. Keep tools sharp and
clean for better and safer performance. Follow
instructions for lubricating and changing accesso
ries. Inspect tool cords periodically and if dam-
aged, have repaired by authorized service center.
Inspect extension cords periodically and replace
if damaged. Keep handles dry, clean, and free
from oil and grease.
14. Disconnect tools. When not in use, before servic-
ing, and when changing accessories, such as
blades, bits, cutters.
15. Remove adjusting keys and wrenches. Form habit
of checking to see that keys and adjusting wrench-
es are removed from tool before turning it on.
16. Avoid unintentional starting. Don’t carry pluggedin
tool with finger on switch. Be sure switch is off
when plugging in.
17. Outdoor use extension cords. When tool is used
outdoors, use only extension cords intended for
use outdoors and so marked.
18. Stay alert. Watch what you are doing. Use com-
mon sense. Do not operate tool when you are
tired.
19. Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended func-
tion. Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center unless otherwise indicated else
where in this handling instructions manual. Have
defective switches replaced by authorized service
center. Do not use tool if switch does not turn
it on and off.
20. Do not use power tools for applications other than
those specified in the Handling Instructions.
21. To ensure the designed operational integrity of
power tools, do not remove installed covers or
screws.
22. Do not touch movable parts or accessories unless
the power source has been disconnected.
23. Use your tool at lower input than specified on the
nameplate; otherwise, the finish may be spoiled
and working efficiency reduced due to motor
overload.
24. Do not wipe plastic parts with solvent. Solvents
such as gasoline, thinner, benzine, carbon tetra-
chloride, alcohol, ammonia and oil containing
chloric annex may damage and crack plastic parts.
Do not wipe them with such solvent. Wipe plastic
parts with a soft cloth lightly dampened with
soapy water.
25. Consult an authorized Service Agent in the event
of power tool failure.
26. Use only genuine HITACHI replacement parts.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi sv 8 sa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi sv 8 sa in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi sv 8 sa

Hitachi sv 8 sa User Manual - English, German, Dutch, French, Italian, Portuguese, Spanish - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info