568909

Hitachi NV65AD3 Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
5
English
(3) Close the nail guide.
Grip the nail guide and knob. Then depress the knob
and turn the nail guide to the right. Nails are loaded by
adapting the above procedures.
NOTE:
The nail guide may not close properly or the nails may
not advance properly if the linked bands or nails do
not enter into the indicated position or the nails come
away from the guide surface or the wire linking the
nails is warped.
(4) Set the change lever
Turn the change lever in the direction of the arrow as
shown in Fig. 6 so that it corresponds to the linking
method for the nails being used.
Fig. 6
NOTE:
If the position of the change lever is not set to the
linking position of the nails to be used, the nails will
not advance properly.
CAUTION:
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a work
bench or floor. Also, never face the nail outlet toward
any part of a person.
HOW TO USE THE NAILER
CAUTIONS:
⅜ Never use the head or body of this device as a
hammer.
⅜ Take precautions to ensure the safety of persons in
the vicinity during operation.
1. Nailing procedures
(1) Method of intermittently driving nails (single shot)
The single-contact change lever is in the single shot
position (See Fig. 8)
This nailer includes a single shot structure to allow
striking of a single nail by pushing down the push
lever and pulling the trigger (see Fig. 7).
CAUTION:
⅜ [Method of intermittently driving nails (single shot)]
explained here is not [Sequential fire]. When Single-
contact Change Lever is at the Single shot position, if
the push lever is pushed up in a state where the trigger
is pulled, only one piece of nail in the nail outlet is
fired: Be careful!
In the event it is used by Sequential fire, use the
Sequential Fire Parts Set of OPTICAL ACCESSORY.
⅜ If you do not pull the trigger quickly and crisply while
in the single shot mode, the nailer will bounce and
shoot several nails instead of just one. To avoid this,
be sure to pull the trigger quickly and crisply.
Fig. 7
Fig. 8
⅜ Push lever
When depressing the nail outlet, be sure to fully lift the
push lever (see Fig. 7) to release the safety lock. Thus,
nails cannot be driven without releasing the safety
lock even though the trigger is pulled.
(2) Method for continuous driving of nails (contact drive)
The single-contact change lever is in the contact driving
position (See Fig. 10).
Use the accessory hexagon bar wrench to turn the
single-contact change lever to the contact driving
position.
First pull back the trigger. Then press the nail outlet on
the place to drive nails. Driving of nails will start. (Fig.
9)
Fig. 9
Plastic Collated
Nails
Change
Lever
Wire Collated
Nails
Single-Contact
Change Lever
Single Shot Position
First, pull the Trigger
Trigger
Push Lever
Next, depress the nail outlet
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi NV65AD3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NV65AD3 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info