Manual Hitachi NR90GC2 (page 11 of 90) (English, German, Dutch, French, Italian, Portuguese, Spanish)

568887

Zoom out

Zoom in

1/90

English

* This Nailer is not recommended for use with from 75 mm (3") to 90 mm (3-1/2") ring shank nails in pressured-

treated lumber.

NR90GC2 NR90GR2

Paper collated strip nails Min. Max. Plastic-collated strip nails Min. Max.

Clipped-head nails Full-head nails

2.9 mm

(.113")

50 mm (2")

3.3 mm

(.131")

90 mm (3-1/2")

3.3 mm

(.131")

50 mm (2")

2.9 mm

(.113")

90 mm (3-1/2")

7 mm

(.286")

7.6 mm

(.3")

7.7 mm

(.303")

6.8 mm

(.266")

STANDARD ACCESSORIES

(1) Eye protector .............................................................. 1

(2) Charger ........................................................................ 1

(3) Case ............................................................................. 1

(4) Hexagonal bar wrench for M5 screw ........................ 1

(attached to body)

(5) Oiler ............................................................................. 1

OPTIONAL ACCESSORIES ......... sold separately

⅜ Fuel Cell .......................................... Code No. 753-600

⅜ Gas Strip Nailer Lubricant

250 cc (8 oz.) oil feeder ............... (Code No. 885-246)

APPLICATIONS

⅜ Floor and wall framing.

⅜ Truss build-up, Window build-up.

⅜ Subflooring and roof decking.

⅜ Wall sheathing.

⅜ Mobile home and modular housing construction.

CHARGING

Before using the power tool, charge the battery as follows.

1. Insert the battery into the charger

Insert the battery firmly while observing its direction,

until it contacts the bottom of the charger (See Fig. 2).

CAUTION

The UC7SD model is the exclusively designed

charger. These cannot charge batteries except the

specified batteries. It is possible to insert the batteries

other than the specified into the charger and some

of them may light up the pilot lamps. However, you

are requested to exercise utmost caution not to

charge batteries other than specified ones because

these can not only be charged but also such actions

can result in the malfunction of chargers.

2. Connect the charger power cord to the receptacle

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

About 60 minutes is required to fully charge the

battery at a temperature of about 20°C. The pilot lamp

goes off to indicate that the battery is fully charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power source

is too low.

When the pilot lamp does not go off even if more than

120 minutes have elapsed after starting of the

charging, stop the charging and contact your HITACHI

AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight, etc.,

just after operation, the charger pilot lamp may

not light up. At that time, cool the battery first,

then start charging.

3. Disconnect the charger power cord from the

receptacle

4. Hold the charger firmly and pull out the battery

NOTE

After charging, pull out batteries from the charger first,

and then keep the batteries properly.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2 – 3 times.

01Eng_NR90GC2_WE_7L 4/14/08, 8:11 PM10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NR90GC2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NR90GC2 Manual

Product: