568887

Hitachi NR90GC2 Manual

8
Zoom out
Zoom in
Previous page
1/90
Next page
English
7
27. Do not use a transformer containing a booster.
28. Do not charge the battery from an engine electric
generator or DC power supply.
29. Always charge indoors.
Because the charger and battery heat slightly during
charging, charge the battery in a place not exposed
to direct sunlight; where the humidity is low and
the ventilation is good.
30. The exploded assembly drawing on this handling
instructions should be used only for authorized
service center.
PRECAUTIONS ON USING GAS STRIP NAILER
1. Safe operation through correct usage.
This tool was designed for driving nails into wood and
similar materials. Use it for its intended purpose only.
2. Be careful of ignition and explosions.
This tool must not be used in a
combustible environment or in
presence of flammable liquids or
gases. This tool produces hot exhaust
gases that may ignite flammable
materials and produces sparks. Since sparks may fly
during nailing, it is dangerous to use this tool near
lacquer, paint, benzine, thinner, gasoline, gas,
adhesives and similar inflammable substances as they
may ignite or explode. Under no circumstances should
this tool therefore be used in the vicinity of such
inflammable material.
3. Explosion and fire hazard.
The fuel cell is an aerosol dispensers
with flammable contents.
Pressured container and the
propellant will remain in the fuel cell.
Failure to follow instructions may
result in explosion or fire.
Keep the power tool, fuel cells and
battery away from sunshine and from
temperature exceeding 50°C (120°F).
Fuel cell and/or battery may burst,
releasing flammable gas.
Do not pierce or burn the container,
even after use.
Do not incinerate, refill, reclaim or
recycle the fuel cell.
Do not spray to a naked flame or
any incandescent material.
Keep away from ignition sources – No smoking.
Keep out of the reach of children.
4. Always wear eye protection (protective goggles).
When operating the power tool,
always wear eye protection, and
ensure that surrounding people wear
eye protection too.
The possibility of fragments of the nails
that were not properly hit entering the
eye is a threat to sight. Eye protection can be bought
at any hardware store. Always wear eye protection
while operating this tool. Use either eye protection
or a wide vision mask over prescription glasses.
Employers should always enforce the use of eye
protection equipment.
5. Protect your ears and head.
When engaged in nailing work please wear ear
mufflers and head protection. Also, depending on
condition, ensure that surrounding people also wear
ear mufflers and head protection.
6. Use outside or well-ventilated areas.
This tool exhausts carbon monoxide
which are a danger to health when
inhaled.
This tool shall not be used in
enclosed or poorly ventilated areas.
Do not inhale.
7. Pay attention to those working close to you.
It would be very dangerous if nails that were not
properly driven in should hit other people.
Therefore, always pay attention to the safety of the
people around you when using this tool. Always
make sure that nobody’s body, hands or feet are
close to the nail outlet.
8. Never point the nail outlet towards people.
Always assume the tool contains
fasteners.
If the nail outlet is pointed towards
people, serious accidents may be
caused if you mistakenly discharge
the tool. When connecting and disconnecting the
battery or fuel cell, during nail loading or similar
operations, be sure the nail outlet is not pointed towards
anyone (including yourself). Even when no nails are
loaded at all, it is dangerous to discharge the tool while
pointing it at someone, so never attempt to do so. No
horseplay. Respect the tool as a working implement.
9. Before using the power tool, check the push lever.
The Push Lever and Chamber operate in conjunction
for this device.
Before using the power tool make sure to check that
the push lever operate properly. Without nails,
fuel cell and battery loaded into the power tool,
check the following.
If abnormal operation occurs, do not use the power
tool until it has been inspected and repaired.
⅜ Pull the Feeder knob with the device facing
upward and press down the Push lever then
confirm that the Push lever securely returns to
its original position.
The Push lever operation becomes especially
heavy in low temperatures and drive operations
may not function.
⅜ With pulling back the feeder knob, the push lever
must move smoothly.
⅜ With pulling back the feeder knob, the trigger
must move smoothly.
Furthermore, with regard to the push lever, please
note that it must never be modified or removed.
10. Use specified nails only.
Never use nails other than those specified and
described in these instructions.
11. Be careful when connecting the battery.
When connecting the battery and loading nails in
order not to fire the tool by mistake, make sure of
the followings.
⅜ Do not touch the trigger.
⅜ Do not allow the firing head to contact with any
surface.
MAX 50°C
(120°F)
01Eng_NR90GC2_WE_7L 4/14/08, 8:11 PM7
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi NR90GC2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NR90GC2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info