Manual Hitachi NR65AK (page 10 of 50) (English, German, Dutch, French, Italian, Spanish)

568873

Zoom out

Zoom in

1/50

English

CAUTIONS:

⅜ To prevent unintentional operation, never touch the

trigger or place the top end of the push lever on a

work bench on floor. Also, never face the nail outlet

toward any part of a person.

HOW TO USE THE NAILER

CAUTIONS

⅜ Never use the head or body of this device as a

hammer.

⅜ Take precautions to ensure the safety of persons in

the vicinity during operation.

⅜ Use only genuine HITACHI heat treated nails for this

NR65AK.

⅜ Be sure to position and insert the first nail point

through the hole in the metal connectors.

⅜ Do not drive nails at an angle of less than 50 degrees,

since the nails can ricochet and hurt yourself or

someone else.

⅜ Always point first nail protruded from the nose away

from yourself and others.

⅜ Do not push tool forward when positioning the first

nail in metal hole. If pushing forward, nail head will

be damaged and broken, or will cause jamming.

1. Nailing procedures

This tool has a Sequential Trip Mechanism (Single

Shot) for use when precision nail placement is

necessary.

You must first depress the nail point where you

want to drive a nail and then pull the trigger.

After the nail is driven, completely release the

trigger and lift the tool off the work surface.

This tool is not designed for contact trip operation

(bounce fire), and not available for contact trip valve

units.

And this tool has a new push lever (safety)

mechanism, this is a different push lever mechanism

from another nailers.

The position of the push lever when the nail feeder is

pulled back is shown as below.

When nails are loaded and the trigger is depressed,

the push lever comes down and when the push lever

touches the workpiece, a nails is driven.

This tool is equipped with a lockout feature that

prevents the tool from being activated when there

are 5 or less nails in the magazine.

There is a method of operation to drive nails with this

Nailer.

It is intermittent operation (Trigger fire) only.

(1) Be sure to position and insert the first nail point

through the hole in the metal connec9tor with finger

off the trigger.

Be sure to position the nail with triangle mark (

) at

noe muzzle. (See Fig. 4)

Keep the tool vertically when driving. (See Fig. 5)

Do not push the tool forward when positionig the

first nail in metal hole. (See Fig. 6)

(2) Pull the trigger to drive a nail with keeping your face

and hands away from the nose muzzle.

(3) Remove finger from the trigger.

Remove the nailer from workpiece and reposition

into the next pre-punched metal hole.

Repeat same process.

(4) When charge the nail length, remove the all nails in

the magazine.

NOTES:

⅜ THIS is a SEQUENTIAL TRIP MECHANISM, and should

be used in accordance with all warnings and

instructions.

⅜ Always handle nails and package carefully. If nails

are dropped, collating paper may be broken.

⅜ After nailing:

(1) disconnect air hose from the Nailer;

(2) remove all nails from the Nailer;

(3) supply 5 – 10 drops of Hitachi pneumatic tool

lubricant into the air plug on the Nailer; and

(4) open the petcock on the air compressor tank to

drain any moisture.

INSPECTION AND MAINTENANCE

CAUTION:

Be sure to disconnect the hose during cleaning

jams, inspection, maintenance and cleaning.

1. Inspecting the magazine

1 DISCONNECT AIR HOSE.

2 Clean the magazine. Remove plastic tips or wooden

tips which may have accumulated in the magazine.

Lubricate it with Hitachi pneumatic tool lubricant.

(See Fig. 7)

2. Check on mounting screws for each part

At regular intervals check every part for loose

mounting screws and whether or not there are any

air leaks. Retighten any loose screws. Operating the

equipment with loose screws untightened will incur

a hazard.

3. Inspecting the push lever

Check if the push lever (Fig. 1) can slide smoothly.

Clean up the sliding area of the push lever and use

the provided oil for lubrication from time to time.

Lubrication enables smooth sliding and

simultaneously serves to prevent the formation of

rust.

4. Storing

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

⅜ When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach of children.

Push Lever

At Non-Firing

Nose

Push Lever

At Firing

Nose

Push Lever

Nose

Workpiece

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NR65AK in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NR65AK Manual

Product: