505963
8
Zoom out
Zoom in
Previous page
1/27
Next page
English - 7 -
Power Connection
IMPORTANT: The set-top box is designed to operate on 12 V DC. For this, an adaptor is used
which gives 12 V voltage. Connect this adaptor to a system that supplies 220-240V AC,50Hz.
After unpacking, allow the set-top box to reach the ambient room temperature before you connect the set
to the mains
UK
Power On-Off
Connect all cables before plugging into the mains. After plugging in the mains cord of the set-top-box to the
mains supply, a light will be seen on the front panel (Standby mode). When the set-top-box is rst powered
up please wait until the box is initialized before activating the receiver since booting of software will take some
time. Make sure that all cable connections are in place. Plug the mains. Please wait until unit is initialized.
This may take almost a minute.
This product conforms the latest European Union Power Consumption Regulations and features low power
standby mode. Product enters into the low power standby mode approximately 2-3 minutes later after you
press standby button to turn off the unit. Until low power mode is activated, clock will be displayed at the
display. When the low power mode is activated, display will be shut down. When you press standby button
during low power mode, it may take a minute until product is initialised. However if you press standby button
before low power mode is activated unit will be initialized in a couple of seconds (Active standby mode).
Although it is not recommended for enviromental reasons, you may disable low power mode in your product
at setup –conguration menu.
Auto Power Down:
This box will automatically switched from active mode into standby mode, after less than three hours in active
mode, following the last user interaction and/or a channel change with an alert message two minutes before
going in to standby mode. The Automatic power-down will be set as default and the user will be able to change
Automatic power down to on or off in the menu
Important Note : If there is any ongoing programme recording or if any EPG programme recordings and/or
manual recordings is set to a nearby time, the unit does not switch to low power mode and remains in active
standby mode until recording tasks have been nished. At low power mode, the unit initializes a couple of
minutes before the actual time of the incoming recording task.
Important Note : The unit initializes time to time to receive updates from EPG broadcast in order to sycnronize
EPG recording tasks properly. After getting updates, the unit switches to low power mode automatically. This
takes a short while and it is not a malfunction.
Antenna Connection
35026858
SCART (TV)
ANTENNA
IN
ANTENNA
OUT
DC IN
OPTICAL
AUDIO OUT
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi HDR505 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi HDR505 in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info