386508
29
Zoom out
Zoom in
Previous page
1/34
Next page
27
English
Use Cap Position
Rotating speed selection (Position of the shift knob)
LOW (Low speed) HIGH (High speed)
Driving
Machine screw 1 5
For 4 mm or smaller diameter
screws.
For 5 mm or larger diameter
screws.
Wood screw 1 5
For 3.5 mm or smaller nominal
diameter screws.
For 3.8 mm or larger nominal
diameter screws.
Drilling
Wood For 10 mm or larger diameters.
For 10 mm or smaller
diameters.
Metal
For drilling with an iron
working drill.
—————
(2) Tightening power indication
Tightening power should be changed according to
the screw type and the materials to be tightened.
Guidance of the tightening power is indicated on
the outer frame of this unit with numerals 1, 2,
3, 4 and 5. The minimum power is from 1
position and bigger the value the stronger is the
power (see Fig. 5).
(3) How to adjusts the tightening power
Rotate the cap and set to one of the numerals.
Adjust the power by cap rotation in such a way that
when the power is too strong, set to the next
smaller numeral and set to the next larger numeral
when too weak.
CAUTION
The motor rotation may be locked to cease while
the unit is used as drill. While operating the driver
drill, take care not to lock the motor.
Too long hammering may cause the screw broken
due to excessive tightening.
3. Change rotation speed
Operate the shift knob to change the rotational
speed. Move the shift knob in the direction of the
arrow (see Figs. 6 and 7).
When the shift knob is set to L, the drill rotates
at a low speed.
When set to H, the drill rotates at a high speed.
CAUTION
When changing the rotational speed with the shift
knob, confirm that the switch is off.
Changing the speed while the motor is rotating will
damage the gears.
When setting the shift knob to H (high speed) and
the position of the cap is 4 or 5, it may happen
that the clutch does not engaged and that the motor
is locked. In suh a case, please set the shift knob
to L (low speed).
If the motor is locked, immediately turn the power
off. If the motor is locked for a while, the motor
or battery may be burnt.
4. The scope and suggestions for uses
The usable scope for various types of work based
on the mechanical structure of this unit is shown
in Table 1.
Work Usable range Suggestions
Drilling
Wood: 15 mm
Use for drilling purpose.Steel: 10 mm
Aluminum: 10 mm
Driving
Machine screw: 6 mm
Use the bit and socket matching the screw
diameter.
Nut: 5 mm
Wood screw: 5.1 mm (diameter) x 35 mm (length) Use after drilling a preparatory hole.
Table 1
×
5. How to select tightening power and rotational speed
Table 2
L
CAUTION
The selection examples shown in Table 2 should
be considered as general standard. As different types
of tightening screws and different materials to be
tightened are used in actual works proper
adjustments are naturally necessary.
6. Mounting and dismounting of the bit.
(1) After inserting a driver bit, etc. into the keyless drill
chuck, firmly grasp the ring and tighten the sleeve
by turning it toward the right (in the clockwise
direction as viewed from the front). (See Fig. 8)
If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger
when the sleeve is tightened.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by
turning it toward the left (in the counter-clockwise
direction as viewed from the front). (See Fig. 8)
CAUTION:
When it is no longer possible to loosen the sleeve,
use a vise or similar instrument to secure the bit.
Set the clutch mode between 1 and 3 and then turn
the sleeve to the loose side (left side) while operating
the clutch. It should be easy now to loosen the
sleeve.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi fds 10 dv at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi fds 10 dv in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi fds 10 dv

Hitachi fds 10 dv User Manual - English, German, Dutch, French, Italian, Portuguese, Spanish - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info