383761
8
Zoom out
Zoom in
Previous page
1/68
Next page
7
English
SPECIFICATIONS
* Be sure to check the nameplate on product as it is subject to change by areas.
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power Input 1010 W*
Capacity Mild Steel Pipe: O.D. 130 mm
Vinyl Chloride Pipe: O.D. 130 mm
Wood: Depth 300 mm
Mild Steel Plate: Thickness 19 mm
No-Load Speed 0 – 2800 min
–1
Stroke 29 mm
Weight (without cord) 3.3 kg
STANDARD ACCESSORIES
(1) Blade (No. 103) ......................................................... 1
(2) Case ............................................................................. 1
(3) Hexagonal bar wrench ............................................. 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
(1) No. 1 Blade (12) No. 103 Blade
(2) No. 2 Blade (13) No. 104 Blade
(3) No. 3 Blade (14) No. 105 Blade
(4) No. 4 Blade (15) No. 106 Blade
(5) No. 5 Blade (16) No. 107 Blade
(6) No. 8 Blade (17) No. 108 Blade
(7) No. 9 Blade (18) No. 121 Blade
(8) No. 95 Blade (19) No. 131 Blade
(9) No. 96 Blade (20) No. 132 Blade
(10) No. 101 Blade (21) Cut-off guide for pipe
(11) No. 102 Blade
(1) – (9) : HCS Blades (HCS : High speed Carbon
Steel)
(10) – (20) : Bl-METAL Blades
Refer to Table 1, 2 and 3 for use of the blades.
Optional accessories are subject to change without notice.
APPLICATIONS
Cutting pipe and angle steel.
Cutting various lumbers.
Cutting mild steel plates, aluminum plates, and
copper plates.
Cutting synthetic resins, such as phenol resin and
vinyl chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirement specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Dust produced in operation
The dust produced in normal operation may affect
the operator’s health. To wear a dust mask is
recommended.
5. Mounting the blade
This unit employs a detachable mechanism that
enables mounting and removal of saw blades
without the use of a wrench or other tools.
(1) Turn on and off the switching trigger several times
so that the lever can jump out of the front cover
completely. Thereafter, turn off the switch and
unplug the power cord. (Fig. 1)
CAUTION
Be absolutely sure to keep the switch turned off
and the power cord unplugged to prevent any
accident.
(2) Push the lever in the direction of the arrow mark
shown in Fig. 2 marked on the lever. (Fig. 2)
(3) Insert the saw blade all the way into the small slit
of the plunger tip with the lever pushing. You can
mount this blade either in the upward or downward
direction. (Fig. 3, Fig. 4)
(4) When you release the lever, the spring force will
return the lever to the correct position automatically.
(Fig. 5)
PRECAUTIONS ON USING RECIPROCATING
SAW
Prior to cutting into walls, ceilings or floors, ensure
there are no electric cables or conduits inside.
01Eng_CR13V_WE 12/1/08, 21:107
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi cr 13 v at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi cr 13 v in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info