383761

Hitachi cr 13 v Manual

10
Zoom out
Zoom in
Previous page
1/68
Next page
9
English
(1) Fasten a workpiece firmly before operation. (Fig. 19)
(2) When cutting metallic materials, use proper machine
oil (turbine oil, etc.). When not using liquid machine
oil, apply grease over the workpiece.
CAUTION
The service life of the saw blade will be drastically
shortened if you don’t use machine oil.
2. Cutting lumber
When cutting lumber, make sure that the workpiece
is fastened firmly before beginning. (Fig. 20)
CAUTION
⅜ Never apply any unreasonable force to the saw
blade when cutting. Also remember to press the
base against the lumber firmly.
3. Sawing curved lines
We recommend that you use the BI-METAL blade
mentioned in Table 2 for the saw blade since it is
tough and hardly breaks.
CAUTION
Delay the feed speed when cutting the material into
small circular arcs. An unreasonably fast feed may
break the blade.
4. Plunge cutting
With this tool, you can perform plunge cutting on
plywood panels and thin board materials. You can
carry out pocket cutting quite easily with the saw
blade installed in reverse as illustrated in Fig. 22,
Fig. 24, and Fig. 26. Use the saw blade that is as
short and thick as possible. We recommend for this
purpose that you use BI-METAL Blade No. 132
mentioned in Table 2. Be sure to use caution during
the cutting operation and observe the following
procedures.
(1) Press the lower part (or the upper part) of the base
against the material. Pull the switch trigger while
keeping the tip of the saw blade apart from the
material. (Fig. 21, Fig. 22)
(2) Raise the handle slowly and cut in with the saw
blade little by little. (Fig. 23, Fig. 24)
(3) Hold the body firmly until the saw blade completely
cuts into the material. (Fig. 25, Fig. 26)
CAUTION
⅜ Avoid plunge cutting for metallic materials. This can
easily damage the blade.
⅜ Never pull the switch trigger while the tip of the
saw blade tip is pressed against the material. If you
do so, the blade can easily be damaged when it
collides with the material.
⅜ Make absolutely sure that you cut slowly while
holding the body firmly. If you apply any
unreasonable force to the saw blade during the
cutting operation, the blade can easily be damaged.
5. Cut off guide for cutting pipe (optional accessory)
NOTE
Please refer to the cut off guide user’s manual for
details on how to use it correctly.
SELECTION OF BLADES
To ensure maximum operating efficiency and results, it
is very important to select the appropriate blade best
suited to the type and thickness of the material to be cut.
NOTE:
⅜ Dimensions of the workpiece mentioned in the table
represent the dimensions when the mounting
position of the base is set nearest to the body of
the reciprocating saw. Caution must be exercised
since dimensions of the workpiece will become
smaller if the base is mounted far away from the
body of the reciprocating saw.
1. Selection of HCS blades
The blade number of HCS blades in Table 1 is
engraved in the vicinity of the mounting position
of each blade. Select appropriate blades by referring
to Tables 1 and 3 below.
Table 1: HCS blades
NOTE
No. 1 – No. 96 HCS blades are sold separately as
optional accessories.
2. Selection of BI-METAL blades
The BI-METAL blade numbers in Table 2 are
described on the packages of special accessories.
Select appropriate blades by referring to Table 2
and 3 below.
Product
Cutting Blade
Code No.
appalication used
Cut-off Outer diameter No. 9
guide (L) 75mm – 165mm No. 131
321113
Blade Thickness
No.
Uses
(mm)
No. 1 For cutting steel pipe less than
105 mm in diameter
2.5 – 6
No. 2 For cutting steel pipe less than
30 mm in diameter
2.5 – 6
No. 3 For cutting steel pipe less than
30 mm in diameter
Below 3.5
No. 4
For cutting and roughing lumber
50 – 70
No. 5
For cutting and roughing lumber
Below 30
No. 8
For cutting vinyl chloride pipe less
than 105 mm in diameter
2.5 – 15
For cutting and roughing lumber
Below 105
No. 9 For cutting mild steel pipe less
than 165 mm in diameter when 2.5 – 6
used with cut off guide
No. 95 For cutting stainless steel pipe
less than 105 mm in diameter
Below 2.5
No. 96 For cutting stainless steel pipe
less than 30 mm in diameter
Below 2.5
01Eng_CR13V_WE 12/1/08, 21:109
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi cr 13 v at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi cr 13 v in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info