654256

Hitachi CM-N10000 Manual

8
Zoom out
Zoom in
Previous page
1/30
Next page
-9- -10-
8. Wipe the
toner
off the head and main body with tissue, etc.
●
●
●
The device will not vibrate unless you apply the head to your skin while touching
the side plate. (Skin sensing function)
If the head is not vibrating, the product is not working.
Power will be automatically turned off if device is unused for 30 seconds.
(Auto-off function)
●
Step 3 "
MOISTURIZE
"
3. Check that the power adaptor is connected to the main body, and press the power switch.
(Fig.10)
The “LOW” level indicator lamp will light, and the “MOISTURIZE” mode indicator
lamp will flash. If another mode indicator lamp flashes, press the mode selector
button to switch the mode.
This mode is to give moisturizing care by making the moisturizing ingredients of the
toner
permeate your skin.
1. Attach a new cotton puff to the main body, and fix it with the ring.
●
Do not use a milky lotion or gel. Saturate the cotton puff with the
toner
until it
seeps through the cotton puff to the rear side.
●
For attaching a cotton puff, see "Preparation for use."
2. Saturate the cotton puff with your regular
toner
.
If the power switch is pressed after the end of the "
MICRO-PAT
" mode, the
"
MOISTURIZE
"
mode is set automatically.
5. Apply the head directly to your skin and move it slowly. (Fig. 6)
●
●
Use this product within approximate 5 minutes.
After 5 minutes have elapsed, the product will stop automatically.
The mode indicator lamp will light, and the product will start to vibrate.
CAUTION
Apply head from center to the out side of your face.
Do not keep the head on the same part of your skin, but move it
around. (Cause of skin trouble or poor health condition)
Do not use this device on the same part of your skin for more than 10 seconds.
If you feel slight current stimulation (a tingling sensation) during use, press the
level selector button to set the "LOW" level.
6. An automatic stop is made when around 5 minutes have elapsed. (Auto-off function)
You will know the automatic stop with the ending sound.
●
Make sure to hold the body with your hand touching either of the right and left side
plates.
●
●
●
6. Apply the cotton puff to your skin and move the product slowly. (Fig. 6)
●
Apply head from center to the out side of your face.
Use this product within approximate 5 minutes.
After 5 minutes have elapsed, the product will stop automatically.
The mode indicator lamp will light, and the product will start to vibrate.
The device will not vibrate unless you apply the cotton puff to your skin while
touching the side plate. (Skin sensing function)
If the head is not vibrating, the product is not working.
Power will be automatically turned off if device is unused for 30 seconds.
(Auto-off function)
5. Hold the main body by the side plate. (Fig. 5)
●
If the moisture in the cotton puff becomes insufficient or if it is hard to slide, add more
toner.
●
Do not use this device on the same part of your skin for more than 10 seconds.
CAUTION
Do not keep the cotton puff on the same part of your skin, but
move it around. (Cause of skin trouble or poor health condition)
●
If you feel slight current stimulation (a tingling sensation) during use, press the
level selector button to set the "LOW" level.
If you still feel a "tingling sensation," add more toner.
9. Remove the ring and the cotton puff.
7. An automatic stop is made when
around
5 minutes have elapsed. (Auto-off function)
You will know the automatic stop with the ending sound.
●
●
Wipe off the surface of the head with tissue, etc.
●
Do not use the cotton puff again once it is used because its reuse will cause
skin trouble.
4. Select the power level ("HIGH" or "LOW") with the level selector button.
●
Every time the level selector button is pressed, the potential power level is
switched between "HIGH" and "LOW"
.
The vibration power does not change.
Select the power level ("HIGH" or "LOW") with the level selector button
according to your skin condition.
Use at the "LOW" level is recommended for people who use this product for the
first time and who feel something unusual.
7. After use, make sure to pull out the power adaptor from the outlet. (Fig.7)
For continued use of the next mode, keep the power adaptor connected.
8. After use, make sure to pull out the power adaptor from the outlet.
(Fig. 7)
For continued use of the next mode, keep the power adaptor connected.
Step 4 “COOL-AESTHETIC”
This mode tighten the pores of your skin by a fresh cooling effect as the head section
surface is approximately 10℃ lower than the ambient temperature.
1. Remove the cotton puff, and wipe the toner off the head section.
2. Check that the power adaptor is connected to the main body, and press the power
switch. (Fig.11)
The level indicator lamp will go out, and the “COOL-AESTHETIC” mode indicator
lamp will flash. If another mode indicator lamp flashes, press the mode selector
button to switch the mode.
●
If the power switch is pressed after the end of the “MOISTURIZE” mode, the
“COOL-AESTHETIC” mode is set automatically.
Use at an ambient temperature in the range of 10 to 40℃.
(Cause of skin damage as the head is too cold if the device is used
at a lower temperature)
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CM-N10000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM-N10000 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info