654256

Hitachi CM-N10000 Manual

7
Zoom out
Zoom in
Previous page
1/30
Next page
-7- -8-
2. Connect the power adaptor to the main body and outlet, and press the power switch.
(Fig. 4)
3. Select the power level ("HIGH" or "LOW") with the level selector button.
●
●
The “LOW” level indicator lamp will light, and the “CLEANSING” mode indicator lamp
will flash. If another mode indicator lamp flashes, press the mode selector button to
select “CLEANSING.”
Every time the level selector button is pressed, the potential power level is
switched between "HIGH" and "LOW". The vibration power does not change.
Select the power level ("HIGH" or "LOW") with the level selector button
according to your skin condition.
●
The previous power level ("HIGH" or "LOW") is stored by the memory function.
Use at the "LOW" level is recommended for people who use this product for the first
time and who feel something unusual.
Make sure to hold the body with your hand touching either of the right and left side
plates.
●
●
●
5. Apply the cotton puff to your skin and move the product slowly. (Fig. 6)
●
Apply head onto skin and slowly head from center to the outside of your face.
Use this product within approximate 5 minutes.
After 5 minutes have elapsed, the product will stop automatically.
The mode indicator lamp will light, and the product will start to vibrate.
The device will not vibrate unless you apply the cotton puff to your skin while
touching the side plate. (Skin sensing function)
If the head is not vibrating, the product is not working.
Power will be automatically turned off if device is unused for 30 seconds.
(Auto-off function)
4. Hold the main body by the side plate. (Fig. 5)
●
If the moisture in the cotton puff becomes insufficient or if it is hard to slide, add more
toner.
●
●
Do not use this device on the same part of your skin for more than 10 seconds.
If you feel slight current stimulation (a tingling sensation) during use, press the
level selector button to set the "LOW" level.
If you still feel a "tingling sensation," add more toner.
How to use
If you sense anything wrong with your skin or body during use,
immediately stop using this product and consult a dermatologist.
(Cause of an accident or poor health condition)
Do not use this product around eyes and ears.
(Cause of an accident or poor physical condition)
CAUTION
Do not keep the cotton puff on the same part of your skin, but
move it around. (Cause of skin trouble or poor health condition)
Step 1
"
CLEANSING
"
This mode is to remove fine dirt remaining in pores which cannot be removed by simple
washing and make your skin suitable for
"
MICRO-PAT
"
.
.
1. After washing your face, saturate the cotton puff attached to the head with toner.
Use your regular toner or wiping lotion with an exfoliating effect.
(Do not use a milky lotion or gel.)
Saturate the cotton puff with the toner until it seeps through the cotton puff to the
rear side.
●
Some toners (made only of mineral spring water or water, etc.) may not show
effects sufficiently.
8. Remove the ring and the cotton puff.
6. An automatic stop is made when around 5 minutes have elapsed.
(Auto-off function)
You will know the automatic stop with the ending sound.
●
●
Wipe off the surface of the head with tissue, etc.
●
Do not use the cotton puff again once it is used because its reuse will cause
skin trouble.
●
1. Evenly spread your regular
toner
over your face.
Step 2 "
MICRO-PAT
"
This mode is to effectively stimulate and loosen up your skin to allow moisturizing
ingredients to easily permeate your skin.
Wipe the
toner
off your hands.
●
Make sure to use the attached power adaptor on an AC power supply of 100 – 240V.
(This product is not rechargeable.)
7. After use, make sure to pull out the power adaptor from the outlet. (Fig. 7)
For continued use of the next mode, keep the power adaptor connected.
Pull out holding the plug portion.
●
The “LOW” level indicator lamp will light, and the “MICRO-PAT” mode indicator lamp
will flash. If another mode indicator lamp flashes, press the mode selector button to
switch the mode.
If the power switch is pressed after the end of the "
CLEANSING
" mode, the
"
MICRO-PAT
" mode is set automatically.
2. Check that the power adaptor is connected to the main body, and press the power switch.
(Fig. 8)
3. Select the power level ("HIGH" or "LOW") with the level selector button.
●
Every time the level selector button is pressed, the power level is
switched between "HIGH" and "LOW"
.
The vibration power does not change.
Select the power level ("HIGH" or "LOW") with the level selector button
according to your skin condition.
Use at the "LOW" level is recommended for people who use this product for the first
time and who feel something unusual.
Make sure to hold the body with your hand touching either of the right and left side
plates.
●
4. Hold the main body by the side plate. (Fig. 9)
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CM-N10000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM-N10000 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info