563833
17
Zoom out
Zoom in
Previous page
1/96
Next page
English
16
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem,
consult your dealer or the Hitachi Authorized Service Center.
Charger
Tool
The Charge lamp does not
go on.
The Charge lamp does not
go off after 4 hours of
charging.
Does not operate.
The power plug is not connected to
an AC outlet.
The battery is not properly
connected to the charger.
The battery or charger electrodes
are soiled.
The battery is extremely hot.
The battery or charger is faulty.
The battery is depleted. (The
battery level warning lamp does
not go on.)
The battery has not been properly
installed.
The blade has been incorrectly
installed.
Foreign matter is lodged in the
blade.
The tool has been used for heavy
work.
The Lock Off button was not
pressed when the switch was
pulled back.
Connect the power plug to an AC
outlet.
Insert the battery so that it is
properly seated in the charger.
Use a cotton swab or other tool to
clean the electrodes.
Allow the battery to properly cool
before charging.
Disconnect the power plug and
consult your dealer or the Hitachi
Authorized Service Center.
When a storage battery with little
power left is not used for an
extended period of time, battery
power may drop so low that it
cannot turn on the battery level
warning lamp. Charge the battery.
Remove the storage battery from the
battery compartment in the tool and
check for foreign matter. Also check
the battery electrodes for soiling.
Make sure that the battery is pressed
in until it clicks into place.
If the blade does not move but the
motor is turning, the blade has
probably been incorrectly installed.
Make sure that the crank holder and
crank cam has been installed.
When there is foreign matter in the
blade, remove the battery and use
a pair of tongs or similar tool to
remove it.
Take great care since the tool may
start operating when the foreign
matter has been removed.
Sap or rust may also prevent the
blade from operating. Use a wire
brush or similar tool to remove sap
or rust.
This is the effect of a function that
protects the battery by turning off
the motor when the tool is exposed
to an excessive load. Release the
switch and remove what caused
the excessive load and pull back
the switch to resume work.
To prevent accidents from
incorrect operation, the Lock Off
switch must be pressed while the
switch is pulled back to start the
motor.
Symptom Possible cause Remedy
01Eng_CH10DL_WE 9/30/09, 16:0216
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CG10-DL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CG10-DL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info