616688
6
Zoom out
Zoom in
Previous page
1/220
Next page
6
English
Read all safety warnings and all instructions.
Always wear eye protection.
Always wear hearing protection.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V Rated voltage
n
0
No-load speed
Switching ON
Switching OFF
Disconnect the battery
Mode selector switch
Lighting mode switch
Always ON (turn o after 2 minute)
Light only SW-ON
Always OFF
Battery capacity
Remaining battery indicator switch
The battery remaining power is nearly empty.
Recharge the battery soonest possible
The battery remaining power is a half.
The battery remaining power is enough.
Prohibited action
NOTE
To prevent the battery power consumption caused by
forgetting to turn o the LED light, the light goes o
automatically in about 2 minutes.
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 204.
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
SPECIFICATIONS
Model C18DBAL
Voltage 18 V
No-Load Speed
4100 min
–1
(Power mode)
2500 min
–1
(Silent mode)
Capacity
Cutting
depth
90° 66 mm
45° 45 mm
Weight* 3.2 kg (BSL1850)
* According to EPTA-Procedure 01/2003
NOTE
Due to HITACHI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
Electronic control
Soft-start
Overload protection
This protection feature cuts o the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
Overheat protection
This protection feature cuts o the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
Rotation speed changeover function (Power mode /
Silent mode)
(Power mode / Silent mode switch function)
Each press of the Mode Selector Switch changes the
operating mode. (Fig. 15)
Silent mode reduces maximum motor RPM enabling
e cient work with less noise.
The Silent Mode Indicator Lamp lights in Silent mode.
When the load increases during Silent mode, the tool will
automatically switch to Power mode and revert back to
Silent mode when the load decreases.
In Power mode, no change is made to Silent mode even
when the load decreases.
NOTE
To enable mode changes, pull the switch once after
installing the battery.
Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the chargers power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red (At 1- second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 23.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi C18DBAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi C18DBAL in the language / languages: All languages as an attachment in your email.

The manual is 28,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info