505940

Hitachi C10FSH Manual

15
Zoom out
Zoom in
Previous page
1/100
Next page
14
English
After placing a suitable wooden piece to sit on the
fence and the table surfaces, fix it with the vise. After
the switch has been turned on and the saw blade has
reached maximum speed, slowly lower the handle to
cut a groove on the guard.
CAUTION
Do not cut the groove too quickly; otherwise the guard
might become damaged.
5. Adjusting the guard (Fig. 6)
(1) In the case of cutting at a right angle or bevel cutting:
Loosen the 6 mm knob bolt, bring the guard lightly in
contact with the materials to be cut and secure. Align
the ink line with the saw blade groove on the guard
and begin operations.
(2) In the case of miter cutting or miter cutting plus bevel
cutting:
Loosen the 6 mm knob bolt, move the guard to the
back, making sure that it is not sticking out from the
fence surface.
6. Using the Vise Assembly (Standard accessory) (Fig. 12)
The vise assembly can be mounted on either the left
fence (Fence (B)), or the right fence (Fence(A)), and
can be raised or lowered according to the height of
the workpiece. To raise or lower the vise assembly,
first loosen the 6 mm knob bolt. The vise shaft has
three locking grooves into which the tip of the 6 mm
wing bolt is designed to fit in order to lock the screw
holder in the desired position. To ensure that the tip
of the 6 mm wing bolt is properly aligned with the
desired locking groove on the vise shaft, simply align
the upper surface of the fence to either of three V-
grooves on the vise shaft surface or to the lower
surface of the screw holder. Therefore, the vise
assembly can be attached in either of three positions
to ensure proper height adjustment.
After adjusting the height, firmly tighten the 6 mm
wing bolt; then turn the upper knob, as necessary, to
securely attach the workpiece in position.
WARNING
⅜ Always firmly clamp or vise to secure the workpiece
to the fence; otherwise the workpiece might be thrust
from the table and cause bodily harm.
CAUTION
⅜ Always confirm that the motor head does not contact
the vise assembly when it is lowered for cutting. If
there is any danger that it may do so, loosen the 6
mm wing bolt and move the vise assembly to a
position where it will not contact the saw blade.
7. Positioning the table insert (Fig. 1)
Table inserts are installed on the turntable. When
shipping the tool from the factory, the table inserts
are so fixed that the saw blade does not contact them.
The burr of the bottom surface of the workpiece is
remarkably reduced, if the table insert is fixed so that
the gap between the side surface of the table insert
and the saw blade will be minimum. Before using the
tool, eliminate this gap in accordance with the
following procedure.
Loosen the three 6 mm machine screws, then secure
the left side table insert and temporarily tighten the 6
mm machine screws of both ends. Then fix a
workpiece (about 200 mm wide) with the vise
assembly and cut it off. After aligning the cutting
surface with the edge of the table insert, securely
tighten the 6 mm machine screws of both ends.
Remove the workpiece and securely tighten the 6 mm
center machine screw. Adjust the right hand table
insert in the same way.
CAUTION
⅜ After adjusting the table insert for right angle cutting,
the table insert will be cut to some extent if it is used
for bevel angle cutting.
When bevel cutting operation is required, adjust the
table insert for bevel angle cutting.
8. Confirmation for use of sub fence
This power tool is equipped with a sub fence. In the
case of direct angle cutting and right bevel angle
cutting, use the sub fence. Then, you can do Left bevel
angle cutting, Right bevel angle cutting and Direct
angle cutting and realize stable cutting of the material
with a wide back face.
WARNING
⅜ In the case of left bevel cutting, turn the sub fence
counterclockwise (Fig. 8). Unless it is turned
counterclockwise, the main body or saw blade may
contact the sub fence, resulting in an injury.
9. Confirmation for use of sub fence (A) (Fig. 11)
In the case of direct angle cutting and angle cutting,
use the sub fence (A). The sub fence (A) can be
installed on the right side of the guide fence. Insert
the rods of the sub fence (A) into the holes in the guide
fence. Tighten the 6 mm bolt which come with the
sub fence (A) to secure the sub fence (A). Then, you
can realize stable cutting of the material with a wide
back face.
WARNING
In the case of right bevel cutting, remove the sub fence
(A). Supposing it is not able to remove it, it will contact
the blade or some part of the tool, causing in serious
injury to operator.
10. Using an ink line
(1) Right angle cutting
Loosen the 6 mm knob bolt and contact the tip of the
guard with the workpiece.
Aligning the ink line on the workpiece with the groove
of the guard, the workpiece is cut on the ink line.
(2) Miter cutting and compound cutting (Miter cutting +
bevel cutting)
Upon lowering the motor section, the lower guard is
raised and the saw blade appears.
Align the ink line with the saw blade.
CAUTION
In some arrangements when the turntable is rotated,
the guard projects from the fence surface. Loosen the
6 mm knob bolt and push the guard to the retracted
position. Never lift the lower guard while the saw
blade is rotating. When cutting at an angle of 35° to
the right or more, please slide the guard to the rear.
The guard and sub-fence will not only make contact
and adversely affect cutting accuracy, this could also
result in damage to the guard.
11. Position adjustment of laser line (Only Model C10FSH)
Ink lining can be easily made on this tool to the laser
marker. A switch lights up the laser marker (Fig. 14).
The laser line is adjusted to the width of the saw blade
at the time of factory shipment. Adjust the positions
of the saw blade and the laser line taking the following
steps to suit the use of your choice.
01Eng_C10FSH_WE 12/6/08, 15:4714
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi C10FSH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi C10FSH in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info