505940

Hitachi C10FSH Manual

14
Zoom out
Zoom in
Previous page
1/100
Next page
13
English
STANDARD ACCESSORIES
(1) 255 mm TCT Saw blade (mounted on tool) ............. 1
(2) Dust bag ...................................................................... 1
(3) 10 mm Box wrench .................................................... 1
(4) Vise Assembly ............................................................ 1
(5) Holder .......................................................................... 1
(6) Sub Fence (A) ............................................................. 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (SOLD SEPARATELY)
(1) Extension Holder and Stopper
(2) Saw blade 255 mm TCT Saw blade (Total teeth: 72)
(3) Crown molding Vise Ass'y (Include Crown molding
Stopper (L))
(4) Crown molding Stopper (L)
(5) Crown molding Stopper (R)
Optional accessories are subject to change without notice.
APPLICATION
⅜ Cutting various types of aluminium sash and wood.
UNPACKING
⅜ Carefully unpack the power tool and all related items
(standard accessories).
⅜ Check carefully to make certain all related items
(standard accessories) are present.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the trigger
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extention cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be kept
as short as practicable.
4. When the power tool is prepared for shipping, its
main parts are secured by a locking pin
Move the handle slightly so that the locking pin can
be disengaged.
During transport, lock the locking pin into the gear
case (Fig. 4).
5. Attach the dust bag to the main unit (Fig. 1)
6. Installation
Ensure that the machine is always fixed to bench.
Attach the power tool to a level, horizontal work bench.
Select 8 mm diameter bolts suitable in length for the
thickness of the work bench.
Bolt length should be at least 25 mm plus the thickness
of the work bench.
For example, use 8 mm × 65 mm bolts for a 25 mm
thick work bench.
ADJUSTING THE POWER TOOL PRIOR TO USE
CAUTION
Make all necessary adjustments before inserting the
plug in the power source.
1. Check to see that the lower guard operates smoothly
CAUTION
⅜ This slide compound miter saw is equipped with a
saw head lock as safety device.
⅜ To lower the saw head to cut, the lock must be released
by pressing the lever (A) with your thumb.
(1) When you push down the handle while pushing the
lever (A), check that the lower guard revolves
smoothly (Fig. 5).
(2) Next, check that the lower guard returns to the original
position when the handle is raised.
2. Checking the saw blade lower limit position (Fig. 7)
Check that the saw blade can be lowered 10 mm to
11 mm below the table insert.
If necessary, adjust as follows:
(1) Loosen the 8 mm wing nut.
(2) Insert your 6 mm hexagon bar wrench from behind
of the tool and turn the 8 mm hexagon socket set
screw to the left (counterclockwise) viewed from
behind of the tool.
(3) Turn the 8 mm depth adjustment bolt, change the
height where the bolt head and the gear case contacts,
and adjust the lower limit position of the saw blade.
One turn of the 8 mm depth adjustment bolt changes
the lower limit position of the saw blade by about 8
mm, and this information can be used as a rough
guide.
(4) Turn the 8 mm hexagon socket set screw to the right
(clockwise) as viewed from behind of the tool, and let
it softly contact the tip of the 8 mm depth adjustment
bolt.
CAUTION
Adjust the lower limit position so that the saw blade
will not cut the turntable or complete cutting cannot
be done.
PRACTICAL APPLICATIONS
CAUTION
⅜ It is dangerous to remove or install the workpiece
while the saw blade is turning.
⅜ When sawing, clean off the shavings from the
turntable.
⅜ If the shavings accumulate too much, the saw blade
from the cutting material will be exposed. Never
subject your hand or anything else to go near the
exposed blade.
1. Tightly secure the material by vise assembly to be
cut so that it does not move during cutting
2. Switch operation
Pulling the trigger turns the switch on. Releasing the
trigger turns the switch off.
3. Base holder adjustment (Fig. 3)
Loosen the 6 mm bolt with the supplied 10 mm box
wrench. Adjust the base holder until its bottom surface
contacts the bench or the floor surface.
4. Cutting a groove on the guard
Holder (A) has a guard (see Fig. 6) into which a groove
must be cut. Loosen the 6 mm knob bolt to retract the
guard slightly.
01Eng_C10FSH_WE 5/31/10, 7:07 PM13
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi C10FSH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi C10FSH in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info