616686
12
Zoom out
Zoom in
Previous page
1/84
Next page
12
English
(2) Avoid recharging at high temperatures.
A back pack power supply will be hot immediately after
use. If such a back pack power supply are recharged
immediately after use, its internal chemical substance
will deteriorate, and the back pack power supply life will
be shortened. Leave the back pack power supply for a
while, and recharge them after they have cooled.
CAUTION
If the back pack power supply are charged while it is
heated because it has been left for a long time in a
location subject to direct sunlight or because the back
pack power supply have just been used, the pilot lamp
of the charger lights up green. In such a case, rst let
the back pack power supply cool, then start charging.
When the charge status ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the back pack power supply
or charger is malfunctioning. Take it to your authorized
Service Center.
Since the built-in microcomputer takes about 3 seconds
to con rm that the back pack power supply being
charged with UC36YRSL is taken out, wait for a minimum
of 3 seconds before reinserting it to continue charging.
If the adapter of back pack power supply is reinserted
within 3 seconds, the back pack power supply may not
be properly charged.
USED AS A POWER SUPPLY FOR CORDLESS
POWER TOOLS (DC 36V)
WARNING
Read the instruction manuals for power tools that are to
be connected beforehand.
Always check to con rm that cordless power tools are
switched o before connecting them to the Back Pack
Power Supply adapter.
1. Check to con rm that the main switch is o . (Fig. 8)
The main switch is o if the green power indicator is not
illuminated when the power switch on the switch panel
is pressed.
2. Put on the Back Pack Power Supply.
Tighten the chest buckle and waist buckle so that there
is no looseness but still easy to move. Then adjust the
length of the band and strap.
3. Check to con rm that the cordless power tool to
be connected is switched o .
Plugging the adapter into the power tool adapter
with the switch set at on may result in unexpected
operations, leading to injury.
Check that the switch to the power tool returns to the o
position when pulled once.
4. Plug the adapter into the cordless power tool. (Fig. 8)
Insert the adapter rmly until it clicks into place in the
same way as the battery.
5. Switch on the main switch and power switch to the
Back Pack Power Supply.
Switch on the Back Pack Power Supply’s main switch.
Then switch on the power switch on the switch panel
to illuminate the power indicator and supply DC 36V of
electrical current to the cordless power tool connected.
6. Switch on the cordless power tool and begin work.
Carry out the required work in accordance with the
details provided in the instruction manual for the
cordless power tool in use.
7. Check the remaining capacity of the battery.
Press the remaining battery capacity switch on the
switch panel periodically and check the indicator to
avoid the power tool from stopping midway through the
work in hand.
8. Terminating electricity supply.
Switch o the cordless power tool in use, and then
switch o the power switch and main switch to the Back
Pack Power Supply.
Automatic power o function (power switch on the
switch panel)
To prevent the wasteful use of the Back Pack Power
Supply, the power will be automatically switched o
after ve hours elapses without it being used with the
power switch on the switch panel left in the on position.
If the main switch is left on, check to con rm that the
power to the cordless power tool or USB device being
used is switched o before pressing the power switch
on the switch panel to resume work.
SWITCH PANEL DISPLAYS (FIG. 9)
Power Switch
The power indicator will be illuminated in green and DC
36V of electrical current will be supplied to the adapter
when the power switch is pressed with the main switch
to the Back Pack Power Supply at the on position.
Remaining Battery Capacity Switch
Press the remaining capacity switch to discover the
remaining capacity with the indicator that is illuminated
in red through ve stages.
If the indicator on the right blinks, it means the battery
has run out and output has ceased. Recharge the
battery in this event.
Warning Indicator
Noti es the user that output has been halted owing to a
problem arising.
(Continual illumination in red)
Carrying out work that constantly requires large
amounts of electrical current and that involves
continual use under harsh conditions, such
as high-temperature environments, will cause
the temperature inside the Back Pack Power
Supply to rise. Output will be halted in this
event to prevent high-temperature damage.
Wait until the Back Pack Power Supply cools
down before resuming work.
(Blinking in red)
Output will be halted to prevent damage in the
event of overloaded operations caused by the
blades in cordless power tools, etc., continuing.
Resolve the reason for the overload, and then
press the power switch to resume operations.
(Swift blinking in red)
There is a possibility that damage has
occurred. Cease operations immediately and
request inspections or repairs.
USED AS A USB POWER SUPPLY (DC 5V)
WARNING
Read the instruction manual for the USB device to be
connected beforehand.
Check to con rm that the USB cable to be connected is
not damaged before using it.
Failure to observe this may result in the outbreak or
smoke or re.
Seal the USB terminal with a rubber cover when not in use.
If dust or other matter adheres to the USB terminal, it
may result in the outbreak of smoke or re.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi BL36200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi BL36200 in the language / languages: All languages as an attachment in your email.

The manual is 2,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info