453432
47
Zoom out
Zoom in
Previous page
1/120
Next page
47
English
RESET
If operations or displays of this unit are at fault:
Many functions of this unit are controlled by microcomputers. Make the units in
standby mode and then press the reset switch when operations or displays are still at
fault in spite of pressing any buttons. There is also need to set stations again because
pressing the reset switch makes the preset stations lost.
TUNER SECTION
TUNER AERIALS
For FM, connect the provided FM feeder antenna (see page 18).
For MW, adjust the position of AM loop antenna (see page 17).
A. STEREO/MONO button (using the remote control unit)
- Auto mode:
When listening to an FM stereo broadcast, set the unit to this mode by pressing the
ST/MONO button. The STEREO indicator lights when the FM stereo broadcast is
received.
- Mono mode:
When the FM stereo reception is noisy, set the unit to MONO MODE by pressing the
ST/MONO button.
- Seek tuning:
Press the UP or DOWN button for one second or more. The unit enters the seek
tuning mode to tune in the nearest station automatically, so the broadcast can be
heard.
- Manual tuning:
Each time the UP or DOWN button is pressed, the unit steps through the current
frequency band. Tuning is done in steps of 50 kHz for FM and 9 kHz for MW.
Note:
When seek tuning to the required station is not possible because the broadcast
signal is too weak, press the UP or DOWN button momentarily to perform manual
tuning.
When the power is set to the STANDBY, or another mode (CD or AUX) is selected,
the last tuned frequency is stored in memory. When the power is switched on again
and BAND button is pressed, the same station will be turned on.
B. Auto preset tuning (using the remote control unit)
This will automatically store any broadcasting stations with strong signals into the
memory (Max. 10 for FM and 10 for MW)
Press the AUTO PRESET button for more than 2 seconds. The frequencies of
stations broadcasting signals can be stored in memory automatically in the order of
increasing frequency.
Bottom view
Press RESET switch inside
the unit with a cocktail stick.
Do not use a metal stick.
046-050(Eng) AX-M10E 7/26/02, 5:19 PM47
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi AX-M10E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi AX-M10E in the language / languages: Dutch as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info