816375
10
Zoom out
Zoom in
Previous page
1/204
Next page
10
English
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (o for 0.5 seconds). In such a case,
rst let the battery cool, then start charging.
When the pilot lamp ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger’s
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 3 2
Charging 4 2
Changing bit*152
Selection operating mode / Switch
operation*263
Mounting and removing the hook 7 3
How to use the LED light*383
Setting the direction of rotation,
engaging the transporting safety
device (switch-on lock) *493
Working with stopper*510 4
Remaining battery indicator*6
(on tool body) 11 4
Remaining battery indicator
(on battery) 12 4
Selecting accessories 193
*1 Changing bit
WARNING
Prevent inadvertent starting: Set manual mode and
remove battery pack from the tool before performing any
retooling.
Inserting and removing the bit:
Remove the stopper.
Insert: Insert the bit in the magnetic bit holder.
Remove: Pull the bit from the magnetic bit holder using
pliers.
Attach the stopper again:
turn and engage in position when mounted.
NOTE
The magnetic bit holder may be removed from the
spindle if the sleeve is pulled back.
*2 Selection operating mode, switch on / o
Set the required operating mode on the dial.
NOTE
When the motor is running, the spindle does not start
until the spindle is pushed in.
Manual mode
Switch on: press the trigger switch. Press in the trigger to
increase the rotational speed.
To switch o release the trigger switch.
Automatic mode
The tool starts automatically when the spindle is pushed
in. This facilitates convenient work. In order to enable
automatic mode, brie y press the trigger switch.
NOTE
The tool switches to sleep mode after 15 minutes without
use. To activate again: press the trigger switch brie y.
WARNING
Risk of injury from inadvertent automatic machine start-
up. In automatic mode, do not touch any rotating parts
such as spindle, bit or magnetic bit holder.
Impulse mode
Protruding screws can be precisely countersunk using
this function. Press trigger switch and countersink the
screw with the attached stopper. To switch o release
the trigger switch.
NOTE
If the amount of protrusion of the screw is small, the
screw may not tighten.
In that case, remove the stopper and make adjustments
in Manual mode.
*3 How to use the LED light
NOTE
The light goes out automatically 10 seconds after the
switch is released.
*4 Setting the direction of rotation, engaging the
transporting safety device (switch-on lock)
CAUTION
Only activate the rotation selector switch when the motor
has completely stopped.
00BookW18DA.indb1000BookW18DA.indb10 2022/05/2318:06:012022/05/2318:06:01
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki W18DB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki W18DB in the language / languages: All languages as an attachment in your email.

The manual is 10.22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info