Manual Hikoki RH650V (page 8 of 48) (English, German, Dutch, French, Italian, Portuguese, Spanish)

816297

Zoom out

Zoom in

1/48

English

BASIC FUNCTIONS

1. Switch Operations and Temperature Adjustments

(Fig. 1, Fig. 2)

Slide the knob upward to activate the switch and enable

continual operations even when your ﬁ nger is removed.

Slide the knob downward as far as it will go to set the

switch at the [0] position and turn it oﬀ .

The position to which the switch is slid will alternate

between modes.

Switch [1] position:

Fixes the wind temperature at 50°C and enables the

wind power to be adjusted.

Switch [2] position:

Enables the wind temperature to be adjusted

between 50°C and 650°C, and enables the wind

power to be adjusted.

2. Adjusting the Temperature (Fig. 1, Fig. 2, Fig. 3)

The temperature can be adjusted between 50°C and

650°C when the switch is at the [2] position.

The temperature will rise by 10°C each time the

Increase Temperature button is pressed (to a maximum

of 650°C.)

Press the button continuously to increase the

temperature in increments of 10°C.

The temperature will decrease by 10°C each time the

Decrease Temperature button is pressed (to a minimum

of 50°C.)

The set temperature will be indicated on the display

when the Increase Temperature and Decrease

Temperature buttons are pressed, but this will return to

the hot wind temperature display after a few seconds.

The temperature will be ﬁ xed at 50°C when the switch is

at the [1] position, and adjustment is not possible.

This is used to quickly cool material that is heat-

warping and to cool the nozzle when it reaches high

temperatures after using the tool.

3. Wind Power Adjustment (Fig. 1, Fig. 3)

The wind power can be adjusted in ﬁ ve stages between

1 and 5. (0.25m3 to 0.5m3)

Press the [+] button to increase wind power, and the [–]

button to decrease wind power.

The tool can be used with it stood pointing upward.

(Fig. 4)

CAUTION

Make sure the tool is placed on a stable surface so that

it won’t topple over when used pointing upward.

4. Attaching the Nozzle (Fig. 5)

CAUTION

The nozzle is extremely hot immediately after use, so

do not touch it.

NOTE

Make sure you do not drop the nozzle.

Replace the nozzle for a type that is suited to the job in hand.

Insert the nozzle supplied ﬁ rmly into the hot wind release

nozzle until it can go no further.

5. Temperature Settings

WARNING

○ Do not use the tool in the vicinity of volatile substances

(thinner, gasoline, etc.)

○ Do not bring the hot wind release nozzle in close

contact with your hands or face during use.

The nozzle is extremely hot immediately after use, so

do not touch it.

Set the temperature in consideration of the article to be

heated.

Also, pay attention to the surrounding material that will be

heated at the same time.

First of all, apply the hot wind from a distance while checking

that there are no changes in the article being heated, and

then move it closer until it reaches an appropriate distance.

Heating inﬂ ammable substances

(paper, wood, plastic, etc.)

Set the switch to the [1] position and apply the heat with

the nozzle at least 10cm away from the article being

heated.

Gently move the tip of the nozzle up, down, left and right

to apply the heat.

Applying heat constantly to one location may result in

malformation or the outbreak of smoke.

Heating non-ﬂ ammable substances

(metal, stone, concrete, etc.)

Set the switch to the [1] position, and if there are no

problems, move it to the [2] position.

Apply the heat with the nozzle at least 5cm away from

the article being heated.

Holding the nozzle too close may result in the tool

overheating, leading to malfunctions.

WORK EXAMPLE

CAUTION

Parts of the nozzles supplied are sharp, so use gloves

when removing them from the case and when attaching

or detaching them.

Select the nozzle in consideration of the shape of the

article being heated and the area being heated.

1. Peeling oﬀ paint (Fig. 6)

Use nozzle (ﬂ at) or nozzle (round) to soften the paint

with the hot wind, and then remove it with the scraper

supplied.

Note that heating the paint too much may result in it

scorching and becoming harder, making it diﬃ cult to

scrape oﬀ .

2. Softening adhesive (Fig. 7)

Use nozzle (ﬂ at) or nozzle (round) to soften the surface

and make it easy to peel, and then pull up one of the

edges, blow heat underneath it and gently peel it oﬀ so

that none of the adhesive remains.

3. Heat wrapping (Fig. 8)

Use nozzle (ﬂ at) to heat-wrap shrink ﬁ lm and tubes. The

material will change color or crack if hot air is blown onto

it from a close distance, so maintain an appropriate

distance while monitoring progress.

4. Forming resin pipes (Fig. 9)

Use nozzle (curved surface) to evenly heat the

circumference of the resin pipe.

To prevent the inside of the pipe from narrowing when

bending it, etc., pour sand inside, block both ends and

then gently bend it.

5. Removing putty from window frames (Fig. 10)

Use nozzle (glass protector) to soften the putty with heat,

and then remove the putty with the scraper supplied.

Note that glass may crack if heat is continually applied

to it.

6. Defrosting water pipes (Fig. 11)

Use nozzle (curved surface) to heat the frozen area from

the edge to the center. Do not mistake water pipes for

glass pipes.

Take care to avoid damaging frozen resin areas on

water pipes.

00BookRH650VWE.indb800BookRH650VWE.indb8 2019/07/249:22:302019/07/249:22:30

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki RH650V in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2.13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hikoki RH650V Manual

Product: