816318

Hikoki M8V2 Manual

8
Zoom out
Zoom in
Previous page
1/116
Next page
8
English
(2) Straight guide (Standard accessory) (Fig. 10)
Use straight guide for chamfering and groove cutting
along the materials side.
Insert the guide bar into the hole in the bar holder, then
lightly tighten the 2 wing bolts (A) on top of the bar
holder.
Insert the guide bar into the hole in the base, then fi rmly
tighten the wing bolt (A).
Make minute adjustments of the dimensions between
the bit and the guide surface with the feed screw, then
fi rmly tighten the 2 wing bolts (A) on top of the bar holder
and the wing bolt (B) that secures the straight guide.
As shown in Fig. 11, securely attach the bottom of the
base to processed surface of the materials. Feed the
router while keeping the guide plane on the surface of
the materials.
4. Adjusting the rotation speed
The M8V2 has an electronic control system that allows
stepless rpm changes.
As shown in Fig. 12, dial position “1” is for minimum
speed, and position “6” for maximum speed.
5. Cutting
CAUTION
○ Wear eye protection when operating this tool.
○ Keep your hands, face and other body parts away from
the bits and any other rotating parts, while operating the
tool.
(1) As shown in Fig. 13, remove the bit from the work pieces
and press the switch lever up to the ON position. Do
not start cutting operation until the bit has reached full
rotating speed.
(2) The bit rotates clockwise (arrow direction indicated on
the base). To obtain maximum cutting eff ectiveness,
feed the router in conformance with the feed directions
shown in Fig. 14.
NOTE
If a worn bit is used to make deep grooves, a high
pitched cutting noise may be produced.
Replacing the worn bit with a new one will eliminate the
high pitched noise.
6 Trimmer Guide (Optional accessory) (Fig. 15)
Use the trimmer guide for trimming or chamfering. Attach
the trimmer guide to the bar holder as shown in Fig. 16.
After aligning the roller to the appropriate position,
tighten the two wing bolts (A) and the other two wing
bolts (B). Use as shown in Fig. 17.
7. Dust Collector Set
Connect the dust collector set cleaner to collect dust.
(1) Mounting the dust collector.
Use a screwdriver to attach the two screws to the base.
(Fig. 18)
Align the holes on the dust collector with the two screws
and attach the dust collector.
Tighten the two knob nuts.
Connect the cleaner to the dust collector. (Fig. 19)
(2) Dismounting the dust collector.
Use a screwdriver to loosen the two screws.
MAINTENANCE AND INSPECTION
1. Oiling
To ensure smooth vertical movement of the router,
occasionally apply a few drops of machine oil to the
sliding portions of the columns and end bracket.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this tool
should ONLY be performed by a HiKOKI AUTHORIZED
SERVICE CENTER.
5. Replacing supply cord
If the supply cord of Tool is damaged, the Tool must be
returned to HiKOKI Authorized Service Center for the
cord to be replaced.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
SELECTING ACCESSORIES
The accessories of this machine are listed on page 110.
For details regarding each bit type, please contact the
HiKOKI Authorized Service Center.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance
with the following code:
Blue: — Neutral
Brown: — Live
As the colours of the wires in the main lead of this tool may
not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
marked with the letter N or coloured black. The wire
coloured brown must be connected to the terminal marked
with the letter L or coloured red. Neither core must be
connected to the earth terminal.
NOTE:
This requirement is provided according to BRITISH
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except The United Kingdom.
000BookM8V2.indb8000BookM8V2.indb8 2022/12/2211:07:532022/12/2211:07:53
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki M8V2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki M8V2 in the language / languages: All languages as an attachment in your email.

The manual is 6.68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info