816284
10
Zoom out
Zoom in
Previous page
1/184
Next page
10
English
Rotation recovery control function
When the motor is stopped due to overloading, if the
cause is eliminated, the motor automatically resumes
operation.
During grinding, if the motor stops due to pressing too
forcefully with the grinder, gently lift the tool body to start
rotation again.
When the motor is stopped for a certain period of time,
it does not recover, for the protection of the unit and for
safety.
Turn it o once and on again to start it.
Overheat protection
This protection feature cuts o the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
Brake function
Brake activates when the trigger is o .
Brake sytstem workable even in a power outage
The brake system works reliably even if there is a power
outage or unplugging during operation in order to avoid
unexpected accident.
NOTE
To prevent the tip tool from falling o , the brake will not
be applied when the switch is released right after startup.
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Attaching and removing the guard
clip*132
Fitting and adjusting the wheel guard*242
Fixing the side handle 5 3
Assembling depressed center wheel*3 *4
63
Assembling cutting wheel and diamond
wheel*3 *473
Switch operation*583
Grinding angle and grinding method*693
Cutting work*710 4
Selecting accessories*8 175
*1 Attaching and removing the guard clip
Pull on the tabs while removing the guard clip.
When attaching the guard clip, ensure that its tabs
(2 locations) are hooked on the rim of the wheel guard.
*2 Fitting and adjusting the wheel guard
The wheel guard can be adjusted to an optimal angle for
the work.
Fix the wheel guard in place where its hole is aligned with
the bump of the lever before use.
*3 Sold separately
*4 WARNING
Before use, be sure to tighten the wheel nut with the
included wrench.
Failure to tighten could result in the wheel nut
loosening when the brake is activated during a stop.
NOTE
The wheel washer (C) is speci cally for this product.
Do not use it for any other product.
*5 When the 0 voltage re-start protection feature has been
activated, return the power switch to the OFF position
and wait for 1 second or more before restarting the
power tool.
*6 Grinding angle and grinding method
Press down the machine evenly on the surface and
move back and forth so that the surface of the workpiece
does not become too hot.
Rough grinding: position the machine at an angle of
15°–30° for the best working results.
When the grinding stone is new, its corner may dig in
when it is pushed forward, so pull back as shown in “a”
during use.
Once the wheel edge is worn, the workpiece can be
ground in both directions.
*7 Cutting work
Always work against the run of the disc. Otherwise there
is the danger of the machine kicking back from the cut
out of control. Guide the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
*8 WARNING
Do not use the following accessories. Doing so may
prevent correct operation of the switch.
Dust collection guard for diamond cutting disc (Code
No. 377085)
Dust collection guard for diamond cutting disc (with
guide roller) (Code No. 377086)
MAINTENANCE AND INSPECTION
WARNING
Be sure to switch power OFF and disconnect the plug
from the receptacle during maintenance and inspection.
Using cracked, deformed or damaged wheels can lead
to wheel breakage and resulting serious injury.
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks
and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Replacing supply cord
If the replacement of the supply cord is necessary, it
has to be done by HiKOKI Authorized Service Center to
avoid a safety hazard.
4. Filter cleaning and inspection
WARNING
Wear protective glasses and a dust mask when cleaning
the lter with an air gun.
Failure to do so may result in inhalation or exposure of
the eyes to debris or dust.
After use, remove any debris or dust adhered to the lter
using a soft brush. (Fig. 11) Check the lter periodically
to ensure that it is free of scratching, chipping, or tearing.
Replace with a new lter if the lter is damaged in any way.
NOTE
If the mesh is clogged and the debris or dust cannot be
removed, detach the lter and clean it with an air gun,
etc. (See “Exchanging the lter set (Fig. 12)”)
5. Exchanging the lter set (Fig. 12)
NOTE
When detaching the lter, be careful not to let debris
enter the tool body.
Leave the lter set attached to the body, except when
cleaning or exchanging the lter set.
00BookG13BYEQ2.indb1000BookG13BYEQ2.indb10 2022/12/2715:35:052022/12/2715:35:05
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki G13BYEQ2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki G13BYEQ2 in the language / languages: All languages as an attachment in your email.

The manual is 7.93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info