816443

Hikoki CS51EAP Manual

10
Zoom out
Zoom in
Previous page
1/216
Next page
English
10
○ Empty the fuel tank before storing the unit/machine. It is
recommended that the fuel be emptied after each use. If
fuel is left in the tank, store so fuel will not leak.
○ Store unit/machine out of the reach of children.
○ Clean and maintain the unit carefully and store it in a dry
place.
○ Make sure stop switch is off when transporting or storing.
○ When transporting or storage, cover chain with guide bar
cover.
If situations occur which are not covered in this manual, take
care and use common sense. Contact HiKOKI Authorized
Service Centers if you need assistance.
WARNING
KICKBACK DANGER (Fig. 2)
One of the most severe dangers when working with a chain
saw is the possibility of kickback. Kickback may occur when
the upper tip of the guide bar touches an object, or when
the wood closes in and pinches the saw chain in the cut. Tip
contact in some cases may cause a lightning fast reverse
reaction, kicking the guide bar up and back toward you.
Pinching the saw chain along the top of the guide bar may
also push the guide bar rapidly back towards you. Either of
these reactions may cause you to lose control of the chain
saw which could result in serious personal injury. Even
though your chain saw has safety built into its design, you
should not rely on these safety features exclusively. Know
where your guide bar tip is at all times. Kickback does occur
if you allow the kickback zone (1) of the guide bar to touch
an object. Do not use that area. Kickback from pinching is
caused by a cut closing and pinching the upper side of the
guide bar. Study your cut and make sure it will open as you
cut through. Maintain control when the engine is running by
always keeping a fi rm grip on the chain saw with your right
hand on the rear handle, your left hand on the front handle
and your thumbs and fi ngers encircling the handles. Always
hold the chain saw with both hands during operation and cut
at high engine speed.
Follow manufacturer’s sharpening and maintenance
instructions for the saw chain. The lack of this maintenance
may increase the possibility of kickback.
SPECIFICATIONS
The SPECIFICATION of this machine are listed in the table
on page 208.
NOTE
All data subject to change without notice.
ASSEMBLY PROCEDURES
WARNING
Switch off the engine before carrying out any checks or
maintenance.
Never try to start engine without side case, guide bar and
chain securely fastened.
1. Pull the front hand guard (2) toward the front handle to
check that the chain brake is disengaged. (Fig. 3)
2. Remove guide bar clamp nuts (3). Remove the side case
(4). (Fig. 4)
3. Install the guide bar (5) onto the bolts (6), then push it
toward the sprocket (7) as far as it will go. (Fig. 5)
4. Confi rm the direction of saw chain (8) is correct as in the
fi gure, and align the chain on the sprocket (7). (Fig. 5)
5. Guide the chain drive links into the bar groove all around
the guide bar.
6. Install the side case (4) onto the bolts (6).
Make sure that the boss of chain tension adjust bolt (9)
fi ts into the hole (10) of the guide bar. (Fig. 5)
The brake lever (12) of the side case must fi t the groove
(11) on the side of the front hand guard.
Then tighten the guide bar clamp nuts (3) by hand that
allows the guide bar end to move up and down easily.
(Fig. 6)
7. Raise the guide bar end, and tighten the chain (8) by
turning the tension adjustment bolt (13) clockwise until
the chain fi ts snugly against underside of guide bar (5).
The chain is correctly tensioned when there is no slack
on the underside of the guide bar. (Fig. 7, 8)
CAUTION
PROPER TENSION IS EXTREMELY IMPORTANT
8. Raise the guide bar end and securely tighten the guide
bar clamp nuts (3) with the combi box spanner (14).
(Fig. 9)
9. A new chain will stretch so adjust the chain after a few
cuts and watch chain tension carefully for the fi rst half
hour of cutting.
NOTE
Check the chain tension frequently for optimum
performance and durability.
CAUTION
○ When the chain is excessively tightened, the guide bar
and chain will be damaged rapidly. Conversely, when
the chain is excessively loosened, it may get out of the
groove in the guide bar.
○ Always wear gloves when touching the chain.
OPERATING PROCEDURES
Fuel (Fig. 10)
WARNING
○ The chain saw is equipped with a two-stroke engine.
Always run the engine on fuel, which is mixed with oil.
Provide good ventilation, when fueling or handling fuel.
○ Fuel is highly fl ammable and it is possible to get seriously
injured when inhaling or spilling on your body.
Always pay attention when handling fuel. Always have
good ventilation when handling fuel inside building.
Fuel
○ Always use branded 89 octane unleaded gasoline.
○ Use genuine two-cycle oil or use a mix between 25:1 to
50:1, please consult about the mixture ratio to HiKOKI
Authorized Service Centers.
○ If genuine oil is not available, use an anti-oxidant added
quality oil expressly labeled for air-cooled 2-cycle engine
use (JASO FC GRADE OIL or ISO EGC GRADE). Do not
use BIA or TCW (2-stroke water-cooling type) mixed oil.
○ Never use multi-grade oil (10 W/30) or waste oil.
○ Never mix fuel and oil in machine’s fuel tank. Always mix
fuel and oil in a separate clean container.
Always start by fi lling half the amount of gasoline, which is
to be used.
Then add the whole amount of oil. Mix (shake) the fuel
mixture. Add the remaining amount of gasoline.
Mix (shake) the fuel-mix thoroughly before fi lling the fuel
tank.
Mixing amount of two-cycle oil and gasoline
Gasoline (Liter) Two-cycle oil (ml)
Ratio 50:1 Ratio 25:1
0.5 10 ——— 20
1 20 ——— 40
2 40 ——— 80
4 80 ——— 160
Fueling (Fig. 11)
WARNING
○ Always shut off the engine and let it cool for a few
minutes before refueling.
000BookCS51EAP.indb10000BookCS51EAP.indb10 2019/01/2410:58:522019/01/2410:58:52
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CS51EAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CS51EAP in the language / languages: All languages as an attachment in your email.

The manual is 42.24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info