816400
5
Zoom out
Zoom in
Previous page
1/152
Next page
5
English
Orbital cutting
Stroke
Disconnect mains plug from electrical outlet
Class II tool
Warning
Prohibited action
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed on page 143.
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting metal and stainless steel pipe.
Cutting various lumbers.
Cutting mild steel plates, aluminum plates, and copper
plates.
Cutting synthetic resins, such as phenol resin and vinyl
chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
SPECIFICATIONS
Voltage (by areas) * (110 V, 220 V, 230 V,
240 V)
Power Input * 1100 W
Capacity
Mild Steel Pipe O.D. 130 mm
Vinyl Chloride
Pipe O.D. 130 mm
Wood Depth 300 mm
Mild Steel Plate Thickness 19 mm
No-Load Speed 0 – 3000 min–1
Stroke 32 mm
Weight (without cord) ** 3.9 kg
* Be sure to check the nameplate on product as it is
subject to change by areas.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Switch Operation 2138
Adjusting operating speed*13139
Adjusting stroke 4139
Mounting the blade 5 139
Dismounting the blade*26 140
When the blade broken*37 140
Adjusting the base 8 140
How to use the hook*49 140
Select a saw blade of the
appropriate length 10 141
Fastening work piece rmly 11 141
Plunge cutting (for wood) 12 141
Plunge cutting with the saw blade
installed in reverse 13 142
Maintenance and inspection of
saw blade mount 14 142
Selecting accessories 144
Refer to Table 1, 2 and 3 for use of the blades.
*1 Adjusting operating speed
CAUTION
Select mode while the trigger switch is released. Failure
to do so could result in malfunction.
Once you connect the power plug to an outlet and switch on
the power, you can change modes with each press of the
mode selector switch.
Speed change mode allows the number of maximum
strokes to be switched between 5 levels: minimum
speed, low speed, middle speed, high speed and Max.
speed.
With speed change mode, the set number of maximum
strokes will be maintained even if there is a change in
load.
Operating speed
Mode Status Operating speed
Transmisson
Mode
Min. 0 – 1200 min-1
Low 0 – 1700 min-1
Middle 0 – 2000 min-1
High 0 – 2500 min-1
Max. 0 – 3000 min-1
*2 Dismounting the blade
CAUTION
Never touch the saw blade immediately after use. The
metal is hot and can easily burn your skin.
(1) After pivoting the lever, point the blade downward. The
blade should fall out on its own. If the blade fails to fall
out, pull it out by hand. (Fig. 6)
*3 When the blade is broken
Even when the saw blade is broken and remains inside
the small slit of the blade holder, it should fall out when
the lever is pivoted and the blade is pointed downward.
If the blade fails to fall out on its own, take it out by using
the procedures described below.
(1) If a part of the broken saw blade is sticking out of the
small slit of the blade holder, pull out the protruding part
and take the blade out.
0000BookCR13VEY.indb50000BookCR13VEY.indb5 2022/02/0215:39:592022/02/0215:39:59
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CR13VEY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CR13VEY in the language / languages: All languages as an attachment in your email.

The manual is 12.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info