816371
7
Zoom out
Zoom in
Previous page
1/172
Next page
7
English
SELECTION OF BLADES
To ensure maximum operating e ciency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut.
The blade number is engraved in the vicinity of the mounting
portion of each blade. Select appropriate blades by referring
to Table 3-5.
Table 3: HCS blades
Blade
No. Uses Thickness
(mm)
No. 2 For cutting steel pipe less than
30 mm in diameter 2.5 – 6
No. 3 For cutting steel pipe less than
30 mm in diameter Below 3.5
No. 5 For cutting and roughing lumber Below 30
No. 96 For cutting stainless pipe less than
30 mm in diameter Below 2.5
Table 4: Bl-METAL blades
Blade
No. Uses Thickness
(mm)
No. 101
For cutting steel and stainless
pipes less than 60 mm in outer
diameter 2.5 – 6
No. 103
For cutting steel and stainless
pipes less than 60 mm in outer
diameter 2.5 – 6
No. 107
For cutting steel and stainless
pipes less than 60 mm in outer
diameter Below 3.5
No. 109
For cutting steel and stainless
pipes less than 60 mm in outer
diameter 2.5 – 6
Table 5: Selection of blades for other materials
Material to
be cut Material
quality Thickness
(mm) Blade No.
Iron plate Mild steel
plate 2.5 – 10 No. 2, 101,
103, 109
Below 3.5 No. 3, 107
Nonferrous
metal Aluminium,
Copper and
Brass
5 – 20 No. 2, 101,
103, 109
Below 5 No. 3, 107
Synthetic
resin Phenol resin,
Melamine
resin, etc.
10 – 50 No. 2, 4, 101,
103
5 – 30 No. 3, 5, 8,
107,109
Vinyl chloride,
Acrylic resin,
etc.
10 – 60 No. 2, 4, 101,
103
5 – 30 No. 3, 5, 8,
107, 109
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turned o the switch and remove the battery
before maintenance and inspection.
1. Inspecting the blade
Continued use of a dull or damaged blade will result in
reduced cutting e ciency and may cause overloading of
the motor. Replace the blade with a new one as soon as
excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
5. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modi ed (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
0000BookCR10DL.indb70000BookCR10DL.indb7 2022/02/0215:26:232022/02/0215:26:23
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CR10DL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CR10DL in the language / languages: All languages as an attachment in your email.

The manual is 10.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info